- 您現在的位置：買賣IC網 > PDF目錄1928 > ISL54212IRTZ-T (Intersil)IC USB SWITCH DUAL SPDT 10TDFN PDF資料下載
參數資料
| 型號： | ISL54212IRTZ-T |
| 廠商： | Intersil |
| 文件頁數： | 15/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC USB SWITCH DUAL SPDT 10TDFN |
| 標準包裝： | 6,000 |
| 功能： | USB 開關 |
| 電路： | 2 x SPDT |
| 導通狀態電阻： | 17.7 歐姆 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 2.5 V ~ 5.5 V |
| 電流 - 電源： | 8µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-TDFN/MLP（3x3） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁
9
FN6556.0
September 18, 2007
signal range of 0V to 400mV with a r(ON) flatness of 0.4Ω.
The r(ON) matching between the D+ and D- switches over
this signal range is only 0.06
Ω ensuring minimal impact by
the switches to USB high speed signal transitions. As the
signal level increases the r(ON) resistance increases. At
signal level of 3.3V the switch resistance is nominally 23
Ω.
The USB switches were specifically designed to pass USB
2.0 high-speed (480Mbps) differential signals typically in the
range of 0V to 400mV. They have low capacitance and high
bandwidth to pass the USB high-speed signals with
minimum edge and phase distortion to meet USB 2.0 high
speed signal quality specifications. See the high-speed eye
diagram in Figure 15.
The USB switches can also pass USB full-speed signals
(12Mbps) with minimal distortion and meet all the USB
requirements for USB 2.0 full-speed signaling. See the
The maximum signal range for the USB switches is from
-1.5V to VDD. The signal voltage at D- and D+ should not be
allow to exceed the VDD voltage rail or go below ground by
more than -1.5V.
The USB switches are active (turned ON) whenever the IN
voltage is ≤0.5V.
Note: Whenever the USB switches are ON the audio drivers
of the CODEC need to be at AC or DC ground or floating to
keep from interfering with the data transmission.
ISL54212 Operation
The sections that follow will discuss using the ISL54212 in the
typical application shown in the block diagram on page 8.
VDD SUPPLY
The DC power supply connected at VDD (pin 1) provides the
required bias voltage for proper switch operation. The part
can operate with a supply voltage in the range of 2.5V to
5.5V.
In a typical USB/Audio application for portable battery
powered devices the VDD voltage will come from a battery or
an LDO and be in the range of 2.7V to 3.6V. For best
possible USB full-speed operation (12Mbps) it is
recommended that the VDD voltage be ≥2.5V in order to get
a USB data signal level above 2.5V.
LOGIC CONTROL
The state of the ISL54212 device is determined by the
voltage at the IN pin (pin 2) and the CTRL pin (pin 10). Refer
to truth-table on page 2 of the data sheet. These logic pins
are 1.8V logic compatible when VDD is in the range of 2.7V
to 3.6V and can be controlled by a standard processor.
The CTRL pin is internally pulled low through a 4M
Ω resistor to
ground and can be tri-stated by the processor. The CTRL
control pin is only active when IN is logic “1”.
The IN pin does not have an internal pull-down resistor and
must not be allowed to float. It must be driven High or Low.
Logic control voltage levels:
IN = Logic “0” (Low) when IN ≤0.5V
IN = Logic “1” (High) when IN ≥1.4V
CTRL = Logic “0” (Low) when ≤0.5V or floating
CTRL = Logic “1” (High) when ≥1.4V
Audio Mode
If the IN pin = Logic “1” and CTRL pin = Logic “1,” the part
will be in the Audio mode. In Audio mode the L (left) and R
(right) 3
Ω audio switches are ON and the D- and D+ 5Ω USB
switches are OFF.
When nothing is plugged into the common connector or a
headphone is plugged into the common connector, the
processor will sense that there is no voltage at the VBUS
pin of the connector and will drive and hold the IN control pin
of the ISL54212 high. As long as the CTRL = Logic “1,” the
ISL54212 part will be in the audio mode and the audio
drivers of the media player can drive the headphones and
play music.
USB Mode
If the IN pin = Logic “0” and CTRL pin = Logic “0” or Logic “1”
the part will go into USB mode. In USB mode, the D- and D+
5
Ω switches are ON and the L and R 3Ω audio switches are
OFF.
When a USB cable from a computer or USB hub is
connected at the common connector, the processor will
sense the presence of the 5V VBUS and drive the IN pin
voltage low. The ISL54212 part will go into the USB mode. In
USB mode, the computer or USB hub transceiver and the
MP3 player or cell phone USB transceiver are connected
and digital data will be able to be transmitted back and forth.
When the USB cable is disconnected, the μprocessor will
sense that the 5V VBUS voltage is no longer connected and
will drive the IN pin high and put the part back into the Audio
or Low Power mode.
Low Power Mode
If the IN pin = Logic “1” and CTRL pin = Logic “0,” the part will
be in the Low Power mode. In the Low Power mode, the audio
switches and the USB switches are OFF. In this state, the
device draws typically 1nA of current.
ISL54212
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54213IRTZ-T | IC USB SWITCH DUAL SPDT 10TDFN |
| ISL54214IRUZ-T | IC USB SWITCH DUAL SP3T 12UTQFN |
| ISL54215IRUZ-T | IC USB SWITCH DUAL SPDT 10UTQFN |
| ISL54216IRUZ-T | IC USB SWITCH SP3T DUAL 12TQFN |
| ISL54217IRUZ-T | IC USB SWITCH DUAL SP3T 12UTQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54212IRUZ-T | 功能描述:IC USB SWITCH DUAL SPDT 10UTQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54213 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:MP3/USB 2.0 High Speed Switch with Negative Signal Handling and Mute Function |
| ISL54213IRTZ | 功能描述:IC USB SWITCH DUAL SPDT 10TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR) |
| ISL54213IRTZ-T | 功能描述:IC USB SWITCH DUAL SPDT 10TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54213IRUZ-T | 功能描述:IC USB SWITCH DUAL SPDT 10UTQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。