- 您現在的位置：買賣IC網 > PDF目錄11181 > ISL54233IRTZ (Intersil)IC MULTIPLEXER PDF資料下載
參數資料
| 型號： | ISL54233IRTZ |
| 廠商： | Intersil |
| 文件頁數： | 18/18頁 |
| 文件大小： | 0K |
| 描述： | IC MULTIPLEXER |
| 標準包裝： | 100 |
| 系列： | * |
ISL54233
9
FN7918.0
December 21, 2011
POWER
The power supply connected at VDD (pin 11) provides power to
the ISL54233 part. Its voltage should be kept in the range of
2.7V to 4.6V. In a typical application, VDD will be in the range of
2.7V to 4.3V and will be connected to the battery or LDO of the
MP3 player or cellphone.
A 0.01F or 0.1F decoupling capacitor should be connected
from the VDD pin to ground to filter out any power supply noise
from entering the part. The capacitor should be located as close
to the VDD pin as possible.
LOGIC CONTROL
The state of the ISL54233 device is determined by the voltage at
the C1 pin (pin 9) and the C0 pin (pin 10). Refer to the “Truth
The C1 pin and C0 pin are internally pulled low through 4M
Ω
resistors to ground and can be tri-stated or left floating.
The C1 pin and C0 pin can be driven with a voltage that is higher
than the VDD supply voltage. They can be driven up to 5.25V with
the VDD supply in the range of 2.7V to 4.6V. Driving the logic
higher than the supply rail will cause the logic current to
increase. With VDD = 2.7V and VLOGIC = 5.25V, ILOGIC current is
approximately 5.5A.
Logic Control Voltage Levels
With VDD in the range of 2.7V to 3.6V the logic levels are: C1,
C0 = Logic “0” (Low) when ≤ 0.5V or Floating. C1, C0 = Logic “1”
(High) when ≥ 1.4V.
ALL SWITCHES OFF Mode
If the C1 pin = Logic “0” and C0 pin = Logic “0” the part will be in
the ALL SWITCHES OFF mode. In this mode, the 3D- and 3D+
data switches, the 2D- and 2D+ data switches, and the 1D- and
1D+ data switches will be OFF (high impedance).
The COM pins can accommodate signals that swing below
ground by as much as -2V. This allows an audio CODEC to be
connected to the COM pins when the device is in the all off state.
USB/DV 1 Mode
If the C1 pin = Logic “0” and C0 pin = Logic “1” the part will go
into USB/DV1 mode. The 1D- and 1D+ switches are ON and the
2D- and 2D+ switches and 3D- and 3D+ will be OFF (high
impedance).
USB/DV 2 Mode
If the C1 = Logic “1” and C0 pin = Logic “0” the part will be in the
USB/DV2 mode. The 2D- and 2D+ switches will be ON and the
1D- and 1D+ switches and the 3D- and 3D+ will be OFF (high
impedance).
USB/DV 3 Mode
If the C1 pin = Logic “1” and C0 pin = Logic “1” the part will be in
the USB/DV3 mode. The 3D- and 3D+ switches are ON, and the
1D- and 1D+ switches and 2D- and 2D+ switches will be OFF
(high impedance).
Printed Circuit Board Design for High
Frequency Performance
In 50 systems, the ISL54233 has a -3dB bandwidth of 1.6GHz
(see Figure 19).
To achieve this high bandwidth requires careful design and layout
of the PCB board. Signal traces must be designed to minimize
reflections and reduce parasitic resistance, inductance and
capacitance that degrade the frequency response performance.
Figure 9 shows a picture of the engineering board used to
measure the frequency response of the ISL54233 part. The
board was specifically design for taking high frequency
bandwidth measurements. The board was made with special
materials and was carefully layed out using RF board techniques
to maximize it for high frequency operation.
The next section, “Board Layout Guidelines”, will provide a list of
the PCB board requirements needed to get the maximum
bandwidth from the ISL54233 part when tested with a 50
Ω
Network Analyzer.
FIGURE 9. RF HIGH FREQUENCY BOARD
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54233IRTZ-T | IC MULTIPLEXER |
| C8051F808-GU | IC MCU 8BIT 16KB FLASH 24QSOP |
| C8051F811-GS | IC MCU 8BIT 16KB FLASH 16SOIC |
| ISL84581IAZ-T | IC MULTIPLEXER 8X1 16QSOP |
| DG403DVZ | IC SWITCH DUAL DPST 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54233IRTZ-T | 功能描述:IC MULTIPLEXER RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54233IRTZ-T7A | 制造商:Intersil Corporation 功能描述:USB 2.0 HS/UART, 12LD 3X3 TQFN IND, 250PS T&R - Tape and Reel 制造商:Intersil Corporation 功能描述:IC MULTIPLEXER 3:1 12TQFN 制造商:Intersil 功能描述:USB 2.0 HS/UART, 12L D 3x3 TQFN IND, 250 |
| ISL54233IRUZ-T | 功能描述:IC INTERFACE RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54233IRUZ-T7A | 功能描述:IC INTERFACE RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤 |
| ISL54301IRZ | 制造商:Intersil Corporation 功能描述:QUAD SPST WITH SERIAL INTERFACE, 4X4 QFN - Rail/Tube 制造商:Intersil 功能描述:QD SPST W/SERIAL INTERFACE 4X4 |
發布緊急采購，3分鐘左右您將得到回復。