- 您現在的位置：買賣IC網 > PDF目錄1928 > ISL54406IRTZ (Intersil)IC SWITCH DUAL SPST 10-TDFN PDF資料下載
參數資料
| 型號： | ISL54406IRTZ |
| 廠商： | Intersil |
| 文件頁數： | 16/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH DUAL SPST 10-TDFN |
| 標準包裝： | 100 |
| 功能： | 開關 |
| 電路： | 2 x SPST - NO |
| 導通狀態電阻： | 2.8 歐姆 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 5 V |
| 電流 - 電源： | 7µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-TDFN/MLP（3x3） |
| 包裝： | 管件 |
| 產品目錄頁面： | 1247 (CN2011-ZH PDF) |
ISL54406
9
FN6578.1
July 14, 2010
Application Block Diagram
Detailed Description
The ISL54406 device is a dual single pole-single throw
(SPST) analog switch that operates from a single DC
power supply in the range of +2.7V to +5V. It was
designed to function as a transient suppressor to
eliminate Click and Pop noise on headphones. It comes in
a 10 Ld (3mmx3mm) TDFN or a tiny 10 Ld
(1.8mmx1.4mm) TQFN package for use in MP3 players,
PDAs, cellphones, and other personal media players.
The part consist of a pair of 2.5Ω audio switches. The
audio switches can accept signals that swing below
ground by as much as -1.5V. They were designed to pass
audio left and right stereo signals that are ground
referenced with minimal distortion.
The ISL54406 was specifically designed for MP3 players,
personal media players and cellphone applications that
require but do not have Click and Pop elimination. See
The ISL54406 contains logic control pins SEL1 and SEL2
that will determine the state of the switch. See the “Truth
Table” on page 2 for a description of each state. A
detailed description of the audio switches are provided in
the section that follows.
Audio Switches
The two 2.5Ω audio switches (L, R) are designed to pass
signals that swing 1.5V above and below ground.
Crosstalk between the audio switches is -90dB over the
audio band. These switches have excellent off-isolation of
110dB over the audio bandwidth with a 32Ω load.
Over a signal range of ±1V (0.707VRMS) with VDD >
2.7V, these switches have an extremely low rON
resistance variation (0.03Ω). They can pass ground
referenced audio signals with very low distortion
(<0.04% THD+N) when delivering 4mW into a 32Ω
headphone speaker load. See Figures 10, 11, 12 and 13
for THD+N performance curves.
The audio drivers should be connected at the LIN and RIN
side of the switch and the speaker loads should be
connected at the LOUT and ROUT side of the switch for
proper Click and Pop elimination. The switches have Click
and Pop circuitry on the LIN and RIN side that is activated
when the SEL1 pin is driven High and SEL2 pin is driven
Low. The audio switches are turned OFF in this state. The
ISL54406 should be put in this mode before powering down
or powering up of the audio source drivers. The high
off-isolation of the audio switches along with the Click and
Pop circuitry will prevent the transients generated during
power-up and power-down of the audio source from getting
through to the headphones, thus eliminating Click and Pop
noise in the headphones. The audio switches are turned ON
and the Click and Pop circuitry disabled whenever SEL1 and
SEL2 is driven High.
ISL54406 Operation
The discussion that follows will describe using the
ISL54406 in the “Application Block Diagram” on page 9.
LOGIC CONTROL
The state of the ISL54406 device is determined by the
logic level at the SEL1 and SEL2 pins. The part has four
states or modes of operation. The Audio Playback Mode,
Audio Mute Mode, Click and Pop Mode, and Shutdown
Mode. Refer to “Truth Table” on page 2 for the logic state
of each mode of operation. The SEL1 and SEL2 pins are
internally pulled low through 4MΩ resistors to ground and
can be left floating to pull the logic pins Low.
Logic Control Voltage Levels:
SEL1 and SEL2 = Logic “0” (Low) when ≤ 0.5V or
Floating.
SEL1 and SEL2 = Logic “1” (High) when ≥ 1.4V
4MΩ
ISL54406
AUDIO
LOUT
ROUT
SEL1
GND
LIN
VDD
SEL2
LOGIC CONTROL
CONTROLLER
4MΩ
CODEC
CLICK AND POP
3.3V
220kΩ
CIRCUITRY
RIN
LSHUNT
RSHUNT
220F
0.1F
6Ω
SPEAKER
LEFT
SPEAKER
RIGHT
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54410IRUZ-T | IC SW USB/AUDIO DUAL SPT 10UTQFN |
| ISL54415IRUZ-T | IC USB SWITCH DUAL SPDT 10UTQFN |
| ISL54500IRUZ-T | IC SWITCH SPDT SGL 6UTDFN |
| ISL54502IHZ-T | IC SWITCH SPDT SOT23-6 |
| ISL54503IRUZ-T | IC SWITCH SPDT SGL 6UTDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54406IRTZ-T | 功能描述:IC SWITCH DUAL SPST 10-TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:2,500 系列:- 功能:視頻交叉點開關 電路:1 x 8:6 導通狀態電阻:- 電壓電源:單電源 電壓 - 電源，單路/雙路(±):3.135 V ~ 5.25 V 電流 - 電源:55mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:24-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1214 (CN2011-ZH PDF) 其它名稱:FMS6502MTC24XTR |
| ISL54406IRUZ-T | 功能描述:IC SWITCH DUAL SPST 10-TQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:2,500 系列:- 功能:視頻交叉點開關 電路:1 x 8:6 導通狀態電阻:- 電壓電源:單電源 電壓 - 電源，單路/雙路(±):3.135 V ~ 5.25 V 電流 - 電源:55mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:24-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1214 (CN2011-ZH PDF) 其它名稱:FMS6502MTC24XTR |
| ISL54409 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Audio/USB 2.0 Wired-OR Switch with Click and Pop Reduction |
| ISL54409_10 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Audio/USB 2.0 Wired-OR Switch with Click and Pop Reduction |
| ISL54409EVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL54409 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。