- 您現在的位置：買賣IC網 > PDF目錄1928 > ISL54500IRUZ-T (Intersil)IC SWITCH SPDT SGL 6UTDFN PDF資料下載
參數資料
| 型號： | ISL54500IRUZ-T |
| 廠商： | Intersil |
| 文件頁數： | 12/13頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH SPDT SGL 6UTDFN |
| 產品培訓模塊： | Patient Monitoring and Diagnostic Equipment Solutions |
| 標準包裝： | 1 |
| 功能： | 開關 |
| 電路： | 1 x SPDT |
| 導通狀態電阻： | 5 歐姆 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 5.5 V |
| 電流 - 電源： | 20nA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-UFDFN |
| 供應商設備封裝： | 6-UTDFN（1.2x1.0） |
| 包裝： | 標準包裝 |
| 其它名稱： | ISL54500IRUZ-TDKR |
8
FN6549.2
November 9, 2009
Supply Sequencing And Overvoltage
Protection
With any CMOS device, proper power supply
sequencing is required to protect the device from
excessive input currents, which might permanently
damage the IC. All I/O pins contain ESD protection
diodes from the pin to V+ and to GND (see Figure 9).
To prevent forward biasing these diodes, V+ must be
applied before any input signals, and the input signal
voltages must remain between V+ and GND.
If these conditions cannot be guaranteed then
precautions must be implemented to prohibit the
current and voltage at the logic pin and signal pins
from exceeding the maximum ratings of the switch.
The following two methods can be used to provide
additional protection to limit the current in the event
that the voltage at a signal pin or logic pin goes below
ground or above the V+ rail.
Logic inputs can easily be protected by adding a 1kΩ
resistor in series with the input (see Figure 9). The
resistor limits the input current below the threshold
that produces permanent damage, and the
sub-microamp input current produces an insignificant
voltage drop during normal operation.
This method is not acceptable for the signal path
inputs. Adding a series resistor to the switch input
defeats the purpose of using a low rON switch.
Connecting Schottky diodes to the signal pins (as
shown in Figure 9) will shunt the fault current to the
supply or to ground, thereby protecting the switch.
These Schottky diodes must be sized to handle the
expected fault current.
Power-Supply Considerations
The ISL54500 construction is typical of most single
supply CMOS analog switches, in that they have two
supply pins: V+ and GND. V+ and GND drive the
internal CMOS switches and set their analog voltage
limits. Unlike switches with a 4V maximum supply
voltage, the ISL54500 5.5V maximum supply voltage
provides plenty of room for the 10% tolerance of 3.6V
supplies, as well as room for overshoot and noise
spikes.
The minimum recommended supply voltage is 1.8V but
the part will operate with a supply below 1.8V. It is
important to note that the input signal range, switching
times, and ON-resistance degrade at lower supply
voltages. Refer to the “Electrical Specifications” tables
starting on page 3 and the ”Typical Performance
Curves” starting on page 9 for details.
V+ and GND also power the internal logic and level
shifters. The level shifters convert the input logic levels
to switched V+ and GND signals to drive the analog
switch gate terminals.
This family of switches cannot be operated with bipolar
supplies because the input switching point becomes
negative in this configuration.
Logic-Level Thresholds
This switch family is 1.8V CMOS compatible (0.5V and
1.4V) over a supply range of 2V to 3.6V (see
still below the 1.8V CMOS guaranteed high output
minimum level of 1.4V, but noise margin is reduced.
The digital input stages draw supply current whenever
the digital input voltage is not at one of the supply
rails. Driving the digital input signals from GND to V+
with a fast transition time minimizes power dissipation.
High-Frequency Performance
In 50Ω systems, the ISL54500 has a -3dB bandwidth
of 350MHz (see Figure 17). The frequency response is
FIGURE 8. V+ SERIES RESISTOR FOR ENHANCED
ESD AND LATCH-UP IMMUNITY
IN
COM
100
Ω
V+
GND
C
OPTIONAL
PROTECTION
RESISTOR
NC
NO
FIGURE 9. OVERVOLTAGE PROTECTION
GND
VCOM
VNX
V+
INX
OPTIONAL
PROTECTION
RESISTOR
OPTIONAL
SCHOTTKY
DIODE
OPTIONAL
SCHOTTKY
DIODE
ISL54500
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54502IHZ-T | IC SWITCH SPDT SOT23-6 |
| ISL54503IRUZ-T | IC SWITCH SPDT SGL 6UTDFN |
| ISL54505IHZ-T | IC SWITCH SPDT SOT23-6 |
| ISL5585GCR-TK | IC SLIC RINGING 3.3V VOB 32-QFN |
| ISL5586DIMZ | IC SLIC RINGING LP HOME 28-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54501 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:+1.8V to +5.5V, 5OHM, Single SPST Analog Switches |
| ISL54501IHZ-T | 功能描述:IC SWITCH SPDT SOT23-6 RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54501IRUZ-T | 功能描述:IC SWITCH SPST 6UTDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54502 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:+1.8V to +5.5V, 5ヘ, Single SPST Analog Switches |
| ISL54502IHZ-T | 功能描述:IC SWITCH SPDT SOT23-6 RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。