5
FN6551.2
October 26, 2009
Total Harmonic Distortion
f = 20Hz to 20kHz, VCOM = 2VP-P,
RL =600Ω
25
-
0.03
-
%
-3dB Bandwidth
Signal = 0dBm, RL = 50Ω
25
-
250
-
MHz
NO or NC OFF Capacitance,
COFF
f = 1MHz, VNO or VNC = VCOM = 0V
25
-
6
-
pF
COM ON Capacitance,
CCOM(ON)
f = 1MHz, VNO or VNC = VCOM = 0V
25
-
18
-
pF
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+ V+ = 3.6V, VIN = 0V or V+
25
-
0.013
-
A
Full
-
0.7
-
A
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, VINL
Full
-
0.5
V
Input Voltage High, VINH
Full
1.4
--
V
Input Current, IINH, IINL
V+ = 3.6V, VIN = 0V or V+
Full
-0.1
0.058
0.1
A
Electrical Specifications - 1.8V Supply Test Conditions: V+ = +1.8V, GND = 0V, VINH = 1V, VINL = 0.4V (Note 10), Unless Otherwise Specified. Boldface limits apply over the operating temperature
range, -40°C to +85°C.
PARAMETER
TEST CONDITIONS
TEMP
(°C)
MIN
MAX
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range,
VANALOG
Full
0
-
V+
V
ON-Resistance, rON
V+ = 1.8V, ICOM = 10mA, VNO or VNC = 0V
to V+, (Note
14, See Figure
5)25
-
6
6.5
Ω
Full
-
7
Ω
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 1.8V, VNO or VNC = 1.5V, RL = 50Ω,
CL = 35pF (see Figure 1, Note 14) 25
-
65
-
ns
Full
-
95
-
ns
Turn-OFF Time, tOFF
V+ = 1.8V, VNO or VNC = 1.5V, RL = 50Ω,
CL = 35pF (see Figure 1, Note 14) 25
-
40
-
ns
Full
-
65
-
ns
Break-Before-Make Time
Delay, tD
V+ = 1.8V, VNO or VNC = 1.5V, RL = 50Ω,
CL = 35pF (see Figure 3, Note 14) Full
-
44
-
ns
Charge Injection, Q
VG = 0, RG = 0Ω, CL = 1.0nF (see Figure 2) 25
-
8.2
-
pC
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, VINL
Full
-
0.4
V
Input Voltage High, VINH
Full
1
--
V
NOTES:
10. VIN = input voltage to perform proper function.
11. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data
sheet.
12. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by
characterization and are not production tested.
13. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal
range.
14. Limits established by characterization and are not production tested.
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.6V, GND = 0V, VINH = 1.4V, VINL = 0.5V
(Note 10), Unless Otherwise Specified. Boldface limits apply over the operating
temperature range, -40°C to +85°C. (Continued)
PARAMETER
TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 11, 12)
TYP
MAX
(Notes 11, 12) UNITS
ISL54503