- 您現在的位置：買賣IC網 > PDF目錄10585 > ISL59604IRZ-T7 (Intersil)IC VIDEO EQUALIZER 20-QFN PDF資料下載
參數資料
| 型號： | ISL59604IRZ-T7 |
| 廠商： | Intersil |
| 文件頁數： | 16/28頁 |
| 文件大小： | 0K |
| 描述： | IC VIDEO EQUALIZER 20-QFN |
| 產品培訓模塊： | ISL5960x MegaQ Overview |
| 標準包裝： | 1,000 |
| 系列： | MegaQ™ |
| 類型： | 視頻均衡器 |
| 應用： | 安全系統，視頻路由 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 20-QFN（4x4） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ISL59601, ISL59602, ISL59603, ISL59604, ISL59605
23
FN6739.2
September 5, 2012
LOCK UNTIL RESET
Lock Until Reset mode is entered by setting address
0x05[1:0] = 10b. Lock Until Reset behavior is the same as
described in the stand-alone mode, with the exception of how to
generate a reset.
To generate a reset via software, select Continuous Update mode
and then return to Lock Until Reset mode (register 0x05[1:0] =
00b then 10b). Toggling INVERT (either the hardware pin or the
software bit) will not cause a reset/re-equalization event.
LOCK UNTIL SIGNAL LOSS
Lock Until Signal Loss mode is entered by setting address
0x05[1:0] = 01b. Lock Until Signal Loss can only be enabled via
the SPI interface.
In the Lock Until Signal Loss mode, MegaQ will freeze the
equalization once the LOCKED pin goes high (in the same way as
Lock Until Reset). Unlike the “Settled” state in the Continuous
Update mode, only a signal loss lasting more than 1ms (typical) will
cause MegaQ to re-equalize the signal when it returns. In this
sense, the Lock Until Signal Loss mode can be considered as
halfway between the Continuous Update mode and the Lock Until
Reset mode. The Lock Until Signal Loss mode is useful, for example,
when testing or demonstrating a system by plugging in multiple
different length cables - it eliminates the need to also generate a
reset. To prevent potentially undesired re-equalization, signal losses
lasting less than 1ms (typical) do not trigger a re-equalization.
MANUAL LENGTH
Manual Length mode is entered by setting address
0x05[1:0] = 11b. Manual Length mode allows the forcing of
specific cable lengths, cable type, DC gains, etc. (see the Register
Listing on the next page). The “Cable Type” bit (0x05 [4]) allows
selection between the two most common cable types for security
video: Cat 5/6 or steel core RG-59 coaxial. However since many
of MegaQ’s automatic functions and adjustments are disabled
in Manual Length mode, performance is almost always worse
than what is achieved in any of the automatic modes. For
example, automatic polarity correction is disabled so the polarity
must be manually set using the INVERT bit. There is no practical
reason to ever use Manual Length mode in normal operation.
Serial Interface Protocol
While MegaQ is designed to work as a stand-alone equalizer, it
does have a serial interface that can be used to control it and
monitor its state.
The serial interface is used to read and write the configuration
registers. It uses three signals (SCK, SD, and SEN) for
programming. The serial clock can operate up to 5MHz
(5Mbits/s). The “Serial Timing Diagram” on page 8 shows the
timing of serial I/O.
A transaction begins when the host microcontroller takes SEN
(serial enable) high. The first 8 bits on the SD (serial data) pin are
latched by MegaQ on the rising edge of SCK (serial clock) to
form the address byte. The MSB of the address byte indicates
whether the operation is a read (1) or a write (0), and the next
seven bits indicate which register is to be read from or written to.
Each read and write operation consists of 16 bits: 8 bits for an
address byte followed by 8 bits of data. See the “Serial Timing
Diagram” on page 8 for more details on using the SPI interface.
WRITE OPERATION
After the address byte is clocked in, the next 8 bits should
contain the data to be sent to the register identified in the
address byte.
READ OPERATION
After the rising edge of the 8th clock after the address byte is clocked in,
the microcontroller should tristate the SD line so MegaQ can begin to
output data on the SD pin (from the register identified in the address
byte), beginning on the 9th rising edge of SCK. The data should be
latched on the falling edge of SCK to allow enough time for the data to
settle. See ““Serial Timing Diagram” on page 8 for more details on how
to read from the registers.
TABLE 2. ADDRESS BYTE FORMAT
0 = Write
1 = Read
A6
A5
A4
A3
A2
A1
A0
(MSB)
(LSB)
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B5J-IV-F2 | CONVERTER MOD DC/DC 36V 150W |
| LTC2453CDDB#TRMPBF | IC ADC 16BIT DELTA SIG 8-DFN |
| TW8806EP-PB2-GRS | IC LCD DISPLAY PROCESSOR 128PQFP |
| VE-B5J-IV-F1 | CONVERTER MOD DC/DC 36V 150W |
| ISL59603IRZ-T7A | IC VIDEO EQUALIZER 20-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59604IRZ-T7A | 功能描述:IC VIDEO EQUALIZER 20-QFN RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:MegaQ™ 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
| ISL59605IRZ | 功能描述:IC VIDEO EQUALIZER 20-QFN RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:MegaQ™ 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND |
| ISL59605IRZ-EVALZ | 功能描述:EVALUATION BOARD FOR ISL5960X RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:MegaQ™ 標準包裝:1 系列:- 主要目的:數字電位器 嵌入式:- 已用 IC / 零件:AD5258 主要屬性:- 次要屬性:- 已供物品:板 相關產品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| ISL59605IRZ-T7 | 功能描述:IC VIDEO EQUALIZER 20-QFN RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:MegaQ™ 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
| ISL59605IRZ-T7A | 功能描述:IC VIDEO EQUALIZER 20-QFN RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:MegaQ™ 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
發布緊急采購，3分鐘左右您將得到回復。