- 您現在的位置：買賣IC網 > PDF目錄16341 > ISL59833IAZ-EVALZ (Intersil)EVAL BOARD FOR ISL59833IAZ PDF資料下載
參數資料
| 型號： | ISL59833IAZ-EVALZ |
| 廠商： | Intersil |
| 文件頁數： | 4/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR ISL59833IAZ |
| 標準包裝： | 1 |
| 系列： | * |
12
FN6334.1
March 5, 2007
with proprietary output stage topology, keeping the output
impedance low over a wide frequency range and making it
possible to easily and effectively drive relatively heavy
capacitive loads (see Figure 11).
THE CHARGE PUMP
The ISL59833 charge pump provides a bottom rail up to
1.65V below ground while operating on a 0V to 3.3V power
supply. The charge pump is internally regulated to one-half
the potential of the positive supply. This internal multi-phase
charge pump is driven by a 110MHz differential ring
oscillator driving a series of inverters and charge storage
circuitry. Each series inverter charges and places parallel
adjoining charge circuitry slightly out of phase with the
immediately preceding block. This generates a negative rail
of about -1.6V with a low amplitude ripple voltage from the
charge pump action. Some of this ripple is coupled into the
output signals at a very low amplitude, as seen in Figure 22.
The ripple on the outputs is typically well below the noise
floor of the signal.
There are two ways to further reduce the output supply
noise:
Add a 120
Ω bead in series between VCC and DVCC. This
reduces the coupling between the charge pump and the
analog amplifier supplies.
Add a 20pF capacitor between the back load 75
Ω resistor
and ground (see “ISL59833 + DC-Restore Solution” on
page 10). This will attenuate frequencies above 100MHz.
The system operates at sufficiently high frequencies that any
related charge pump noise is far beyond standard video
bandwidth requirements. Still, appropriate bypassing
discipline must be observed, and all pins related to either the
power supply or the charge pump must be properly
bypassed. See “Power Supply Bypassing and Printed Circuit
IN+
IN-
BIAS
OUT
FIGURE 27. SIMPLIFIED SCHEMATIC
ISL59833
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B70-EY-S | CONVERTER MOD DC/DC 5V 50W |
| EET-UQ2G221JA | CAP ALUM 220UF 400V 20% SNAP |
| ADM6316AY29ARJZ-R7 | IC SUPERVISOR WATCHDOG SOT23-5 |
| VI-BV0-EY-S | CONVERTER MOD DC/DC 5V 50W |
| VI-B10-EY-S | CONVERTER MOD DC/DC 5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59833IAZ-T7 | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ISL59834 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Channel, Single Supply, Video Reconstruction Filter with On-Board Charge Pump |
| ISL59834IRZ | 功能描述:有源濾波器 ISL9104AIRUW EVALBRD 1 6LD U 1 2V RHS RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| ISL59837 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:200MHz Single Supply Video Driver With Charge Pump and Power Down |
| ISL59837IAZ | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。