- 您現在的位置：買賣IC網 > PDF目錄383138 > ISL59837 (Intersil Corporation) 200MHz Single Supply Video Driver With Charge Pump and Power Down PDF資料下載
參數資料
| 型號： | ISL59837 |
| 廠商： | Intersil Corporation |
| 英文描述： | 200MHz Single Supply Video Driver With Charge Pump and Power Down |
| 中文描述： | 200MHz的單電源視頻驅動器，電荷泵和掉電 |
| 文件頁數： | 13/14頁 |
| 文件大?。?/td> | 342K |
| 代理商： | ISL59837 |
13
FN6335.1
March 5, 2007
designed to drive three channels; simply deal with each
channel separately as described in this section.
DC-RESTORE
When the ISL59837 is AC-coupled it becomes necessary to
restore the DC reference for the signal. This is accomplished
with a DC-restore system applied between the capacitive
"AC" coupling and the input of the device. Refer to
“ISL59837 + DC-Restore Solution” on page 10.
DISABLE/POWER-DOWN
The ISL59837 can be disabled and its output placed in a
high impedance state. The turn-off time is around 25ns and
the turn-on time is around 200ns. When the PD pin is taken
high, the chip’s total supply current is reduced to 0.1mA
typically, all but eliminating the power used by the part.
Taking the EN pin high powers down the amplifiers, leaving
the charge pump running. Both pins can be controlled by
standard TTL or CMOS signal levels (0.8V V
IL
, 2.0V V
IH
relative to GND).
OUTPUT DRIVE CAPABILITY
The ISL59837 does not have internal short-circuit protection
circuitry. A short-circuit current of 80mA sourcing and 150mA
sinking for the output is connected half way between the rails
with a 10
Ω
resistor. If the output is shorted indefinitely, the
power dissipation could easily increase such that the part will
be destroyed. Maximum reliability is maintained if the output
current never exceeds ±40mA, after which the electro-migration
limit of the process will be exceeded and the part will be
damaged. This limit is set by the design of the internal metal
interconnections.
POWER DISSIPATION
With the high output drive capability of the ISL59837, it is
possible to exceed the
+
150°C absolute maximum junction
temperature under certain load current conditions.
Therefore, it is important to calculate the maximum junction
temperature for an application to determine if load conditions
or package types need to be modified to assure operation of
the amplifier in a safe operating area.
The maximum power dissipation allowed in a package is
determined according to Equation 1:
T
JA
Where:
T
JMAX
= Maximum junction temperature
T
AMAX
= Maximum ambient temperature
θ
JA
= Thermal resistance of the package
The maximum power dissipation actually produced by an IC
is the total quiescent supply current times the total power
supply voltage, plus the power in the IC due to the load, or:
for sourcing:
for sinking:
Where:
V
S
= Supply voltage
I
SMAX
= Maximum quiescent supply current
V
OUT
= Maximum output voltage of the application
R
LOAD
= Load resistance tied to ground
I
LOAD
= Load current
i = Number of output channels
By setting the two P
DMAX
equations equal to each other, we
can solve the output current and R
LOAD
to avoid the device
overheat.
Power Supply Bypassing and Printed Circuit
Board Layout
Strip line design techniques are recommended for the input
and output signal traces. As with any high frequency device,
a good printed circuit board layout is necessary for optimum
performance. Lead lengths should be as short as possible.
The power supply pin must be well bypassed to reduce the
risk of oscillation. For normal single supply operation, where
the V
S
- pin is connected to the ground plane, a single 4.7μF
tantalum capacitor in parallel with a 0.1μF ceramic capacitor
from V
S
+ to GND will suffice. This same capacitor
combination should be placed at each supply pin to ground if
split-internal supplies are to be used. In this case, the V
S
-
pin becomes the negative supply rail.
For good AC performance, parasitic capacitance should be
kept to a minimum. Use of wire-wound resistors should be
avoided because of their additional series inductance. Use
of sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance can result in
compromised performance. Minimizing parasitic capacitance
at the amplifier's inverting input pin is also very important.
PD
MAX
T
–
--------------------------------------------
=
(EQ. 1)
PD
MAX
V
S
I
SMAX
V
S
V
OUT
i
–
(
)
+
×
V
i
L
-----------------
×
=
(EQ. 2)
PD
MAX
V
S
I
SMAX
V
OUT
i
V
S
–
(
)
+
×
I
LOAD
i
×
=
(EQ. 3)
ISL59837
相關PDF資料 |
PDF描述 |
|---|---|
| ISL59837IAZ | 200MHz Single Supply Video Driver With Charge Pump and Power Down |
| ISL59837IAZ-T7 | 200MHz Single Supply Video Driver With Charge Pump and Power Down |
| ISL59885IS | Auto-Adjusting Sync Separator for HD and SD Video |
| ISL59885ISZR5218 | Circular Connector; No. of Contacts:15; Series:; Body Material:Aluminum; Connecting Termination:Solder; Connector Shell Size:14; Circular Contact Gender:Socket; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:14-15 |
| ISL59885IS-T13 | Auto-Adjusting Sync Separator for HD and SD Video |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59837IAZ | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59837IAZ-EVALZ | 功能描述:EVAL BOARD FOR ISL59837IAZ RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL59837IAZ-T7 | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ISL59885 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Auto-Adjusting Sync Separator for HD and SD Video |
| ISL59885_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Auto-Adjusting Sync Separator for HD and SD Video |
發布緊急采購，3分鐘左右您將得到回復。