- 您現在的位置：買賣IC網 > PDF目錄383139 > ISL6118LIBZA (INTERSIL CORP) Dual Power Supply Controller PDF資料下載
參數資料
| 型號： | ISL6118LIBZA |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Dual Power Supply Controller |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | LEAD-FREE, PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 454K |
| 代理商： | ISL6118LIBZA |
7
Using the ISL6118EVAL1 Platform
Upon proper bias the PPTC, F1, has a nominal 400mA load
current passing through it which is the hold current rating for
that particular device. Removal of the PPTC is necessary to
isolate the ISL6118 as the PPTC load current is common to
the ISL6118EVAL1 bias connections.
By enabling either or both of the ISL6118H switches by
signaling TP3 and/or TP4 high (>2.4V) these switches are
also loaded with a nominal 400mA current.
Provided test points enable the evaluation of voltage loss
across the PPTC (TP9 - TP10) and likewise across the
ISL6118 enabled switches (TP9 - TP6 and TP7). Expect to
see 100% - 300% greater voltage loss across the PPTC than
the ISL6118 (see Figure 11 for ISL6118 vs PPTC voltage
loss comparison).
An overcurrent (OC) condition can be invoked on both the
ISL6118 and the PPTC by driving TP11 to +6V, causing SW1
to close and a nominal 0.94mA load is imposed. This
represents a current overload to the ISL6118 and is thus
quickly current regulated to the 600mA limit. If the OC
duration extends beyond the nominal 12ms of the internal
ISL6118 timer then the output is latched off and the fault
output is asserted by being pulled low turning on the
appropriate FAULT LED. (Please note: the labeling for the
FAULT-1 and FAULT-2 is reversed.) The eval board is
designed to only invoke a OC condition on channel 2 (TP4)
so that a channel to channel isolation evaluation in the
presence of a OC condition can be evaluated.
The primary function of any OC protection device is to
quickly isolate the voltage bus from a faulty load. Unlike the
PPTC and other vendor available IC products, the ISL6118
internal timer that starts upon OC detection provides
consistent protection that is independent of temperature.
Figures 11 through 13 illustrate the comparative efficiency
and effectiveness of the ISL6118 vs the PPTC in protecting
and isolating a faulty load capable from drooping the system
bus in that system.
FIGURE 11. ISL6118 vs PPTC INTO 8.2
LOAD
FIGURE 12. ISL6118 vs PPTC INTO 3.5
LOAD
FIGURE 13. ISL6118 vs PPTC WITH EXTENDED 3.5
LOAD
Typical Performance Curves
(Continued)
VOLTAGE (0.5V/DIV)
V
3.32V
ISL6118
V
OUT
3.29V (0.075
)
0.4A HOLD
CURRENT PPTC
2.93V (1.1
)
GND
VOLTAGE (0.5V/DIV)
TIME (4ms/DIV)
VIN
ISL6118 CR
12ms PERIOD
0.4A HOLD CURRENT PPTC OUT
ISL6118 OUT
VOLTAGE (0.5V/DIV)
TIME (4s/DIV)
ISL6118 OUT
0.4A HOLD CURRENT PPTC OUT
VIN
2.3V AT 10s
1.5V AT 30s
ISL6118
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6118LIBZA-T | Dual Power Supply Controller |
| ISL6AHPEVAL1 | Dual Power Supply Controller |
| ISL6AHPEVAL1-T | Dual Power Supply Controller |
| ISL6118HIB | Dual Power Supply Controller |
| ISL6118HIB-T | Dual Power Supply Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6118LIBZA-T | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Power Supply Controller |
| ISL6119 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:USB Dual Port Power Supply Controller |
| ISL6119EVAL1 | 功能描述:EVALUATION PLATFORM ISL6119 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6119EVAL1-T | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:USB Dual Port Power Supply Controller |
| ISL6119HIB | 功能描述:IC CTRLR DUAL PWR SUPPLY 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。