- 您現在的位置：買賣IC網 > PDF目錄383143 > ISL6226EVAL1 (Intersil Corporation) Advanced PWM and Linear Power Controller for Portable Applications PDF資料下載
參數資料
| 型號： | ISL6226EVAL1 |
| 廠商： | Intersil Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Advanced PWM and Linear Power Controller for Portable Applications |
| 中文描述： | 先進的PWM和線性電源控制器，用于便攜式應用 |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 384K |
| 代理商： | ISL6226EVAL1 |
15
Selection of the output capacitors is also dependent on the
output inductor so some inductor analysis is required to
select the output capacitors.
One of the parameters limiting the converter’s response to a
load transient is the time required for the inductor current to
slew to it’s new level. Given a sufficiently fast control loop
design, the ISL6226 will provide either 0% or 93% duty cycle
in response to a load transient. The response time is the
time interval required to slew the inductor current from an
initial current value to the load current level. During this
interval the difference between the inductor current and the
transient current level must be supplied by the output
capacitor(s).
Minimizing the response time can minimize the
output capacitance required. Also, if the load transient rise
time is slower than the inductor response time, as in a hard
drive or CD drive, this reduces the requirement on the output
capacitor.
The maximum capacitor value required to provide the full,
rising step, transient load current during the response time of
the inductor is:
Where: C
OUT
is the output capacitor(s) required, L
O
is the
output inductor, I
TRAN
is the transient load current step, V
IN
is the input voltage, V
OUT
is output voltage, and DV
OUT
is
the drop in output voltage allowed during the load transient.
High frequency capacitors initially supply the transient
current and slow the load rate-of-change seen by the bulk
capacitors. The bulk filter capacitor values are generally
determined by the ESR (Equivalent Series Resistance) and
voltage rating requirements as well as actual capacitance
requirements. The output voltage ripple is due to the inductor
ripple current and the ESR of the output capacitors as
defined by:
where,
is calculated in the Inductor Selection section.
High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load
circuitry for specific decoupling requirements.
Use only specialized low-ESR capacitors intended for
switching-regulator applications, at 300kHz, for the bulk
capacitors. In most cases, multiple electrolytic capacitors of
small case size perform better than a single large case
capacitor.
The stability requirement on the selection of the output
capacitor is that the ‘ESR zero’, f
Z
, be between 1.8kHz and
45kHz. This range is set by an internal, single compensation
zero at 9kHz. The ESR zero can be a factor of five on either
side of the internal zero and still contribute to increased
phase margin of the control loop. Therefore:
In conclusion, the output capacitors must meet three criteria:
1. They must have sufficient bulk capacitance to sustain the
output voltage during a load transient while the output
inductor current is slewing to the value of the load
transient
2. The ESR must be sufficiently low to meet the desired
output voltage ripple due to the output inductor current,
and
3. The ESR zero should be placed, in a rather large range,
to provide additional phase margin.
Output Inductor Selection
The output inductor is selected to meet the output voltage
ripple requirements. The inductor value determines the
converter’s ripple current and the ripple voltage is a function
of the ripple current and output capacitor(s) ESR. The ripple
voltage expression is given in the capacitor selection section
and the ripple current is approximated by the following
equation:
where F
s
is the switching frequency.
Input Capacitor Selection
The important parameters for the bulk input capacitor(s) are
the voltage rating and the RMS current rating. For reliable
operation, select bulk input capacitors with voltage and
current ratings above the maximum input voltage and largest
RMS current required by the circuit. The capacitor voltage
rating should be at least 1.25 times greater than the
maximum input voltage and 1.5 times is a conservative
guideline.
The AC RMS input current varies with load. Depending on
the specifics of the input power and it’s impedance, most (or
all) of this current is supplied by the input capacitor(s).
Use a mix of input bypass capacitors to control the voltage
ripple across the MOSFETs. Use ceramic capacitors for the
high frequency decoupling and bulk capacitors to supply the
RMS current. Small ceramic capacitors can be placed very
close to the upper MOSFET to suppress the voltage induced
in the parasitic circuit impedances.
For board designs that allow through-hole components, the
Sanyo OS-CON series offer low ESR and good
temperature performance.
For surface mount designs, solid tantalum capacitors can be
used, but caution must be exercised with regard to the
C
OUT
L
I
OUT
×
IN
)
2
×
--------------–
I
OUT
--------------------
×
=
V
RIPPLE
IL
ESR
×
=
IL
C
OUT
f
Z
×
-------------------------------------------
=
IL
V
-------------------------------
V
–
S
V
IN
---------------
×
=
ISL6226
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6226CA | Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 |
| ISL6232 | Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 |
| ISL6232CAZA-T | High Efficiency System Power Supply Controller for Notebook Computers |
| ISL6232CAZA | High Efficiency System Power Supply Controller for Notebook Computers |
| ISL6235 | Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6227 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Mobile-Friendly PWM Controller with DDR Option |
| ISL6227_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Mobile-Friendly PWM Controller with DDR Option |
| ISL6227CA | 功能描述:IC CONTROLLER DDR, DDR2 28QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6227CA-T | 功能描述:IC CONTROLLER DDR, DDR2 28QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6227CAZ | 功能描述:電流型 PWM 控制器 VER OF ISL6227CA RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。