- 您現在的位置：買賣IC網 > PDF目錄383143 > ISL6232CAZA (INTERSIL CORP) High Efficiency System Power Supply Controller for Notebook Computers PDF資料下載
參數資料
| 型號： | ISL6232CAZA |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | High Efficiency System Power Supply Controller for Notebook Computers |
| 中文描述： | 2 A DUAL SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | ROHS COMPLIANT, PLASTIC, QSOP-28 |
| 文件頁數： | 18/25頁 |
| 文件大小： | 746K |
| 代理商： | ISL6232CAZA |
18
FN9116.0
April 18, 2005
its own internal digital soft-start circuit. In shutdown or
standby mode, the soft-start output is reset to zero.
Fault Protection
Undervoltage Protection
When the output undervoltage is detected at below 75%
(typ) of the regulation output for 20ms blanking time, it enters
the discharge mode by discharging the output through the
internal 20
switch connected from PHASE to PGND. When
the output voltage drops below 0.3V, the external low side
MOSFET is latched on to discharge the output to ground.
When either output is in UVP, both outputs are latched off
through soft-discharge. The latches can be reset by toggling
V
IN
, SHDN#, or EN.
Overvoltage Protection
When either output voltage is above 113% (typ) of the
regulation point, both outputs are latched off by turning on
the low side MOSFET and turning off the high side MOSFET.
Discharging the output capacitors through the inductor and
low-side MOSFET causes negative output voltage. For loads
that cannot tolerate a negative voltage, place a 1A power
Schottky diode across the output to act as a reverse-polarity
clamp. If the overvoltage is due to a short in the high side
MOSFET, the battery fuse will be blown and isolated from
the output.
Overcurrent Protection
The output current is continuously monitored through either
an accurate sensing resistor or the DCR of the inductor.
When the inductor peak current reaches the overcurrent limit
threshold, it immediately turn off the high side MOSFET and
turn on the low side MOSFET. This peak current limiting
prevents inductor saturation. If the overcurrent or short
circuit condition is detected for more than 20mS (typical), the
high side MOSFET is latched off and the output is
discharged through the internal 20
switch connected from
PHASE to PGND. When the output voltage drops below
0.3V, the low side MOSFET is latched on to discharge the
output to ground. When either output is latched off due to
overcurrent, the other output is also latched off through soft-
discharge.
Thermal Protection
Thermal-overload protection limits total power dissipation in
the device. When the junction temperature exceeds 150°C,
a thermal sensor forces most of the internal circuitry into
shutdown mode, thus allowing the device to cool down. The
thermal sensor turns the device on again after the junction
temperature drops by 25°C, causing a pulsed output during
continuous overload conditions. The digital soft-start
sequence begins after the thermal shutdown condition is
removed.
Power-Up Sequence
EN3 and EN5 control the power-up sequencing of buck
controllers. Setting EN above 2.4V enables the outputs, and
setting EN below 0.8V disables the outputs. Connecting EN3
or EN5 to REF forces the respective output off until the other
output reaches 90% of the regulation point and soft-start
cycle has ended. One of the buck controllers can remain on
even though the other buck controller turns off. Table 2
shows the power sequence selection.
SHUTDOWN MODE
When SHDN# is set below 0.8V, the part is completely shut
down with a 5μA (typ) shutdown V
IN
current. When SHDN#
is set above 2.4V, both LDO outputs and REF are active.
This is prerequisite for enabling buck controllers. For
automatic shutdown and startup, SHDN# can be tied to V
IN
.
Table 3 is the summary of various operation modes.
TABLE 2. POWER-UP SEQUENCE TABLE
SHDN#
EN3
EN5
LDO3
LDO5
5V BUCK
3.3V
BUCK
Low
x
x
OFF
OFF
OFF
OFF
High
Low
Low
ON
ON
OFF
OFF
High
Low
High
ON
ON
ON
OFF
High
High
Low
ON
ON
OFF
ON
High
High
High
ON
ON
ON
ON
High
High
REF
ON
ON
ON after
3.3V up
ON
High
REF
High
ON
ON
ON
ON after
5V up
ISL6232
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6235 | Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 |
| ISL6235CA | Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 |
| ISL6244CR | Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 |
| ISL6244HR-T | Test Probe; Range:-32deg to 500degF RoHS Compliant: NA |
| ISL6244HRZ | Multi-Phase PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6232CAZA-T | 功能描述:熱插拔功率分布 W/ANEAL HI EFF SYSTM PWR SUPPLY CONTR RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| ISL6232CAZ-T | 制造商:Intersil Corporation 功能描述:LEAD-FREE HI EFFICIENCY SYSTEM PWR SUPPLY CONTR FOR NOTEBOOK - Tape and Reel |
| ISL6232EVAL1 | 功能描述:EVALUATION BOARD 1 ISL6232 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6235 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Advanced Triple PWM Only Mode and Dual Linear Power Controller for Portable Applications |
| ISL6235CA | 制造商:Rochester Electronics LLC 功能描述:SYSTEM ELECTRONICS REGULATOR FOR LCD-PC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。