- 您現在的位置：買賣IC網 > PDF目錄383143 > ISL6235CA (INTERSIL CORP) Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6235CA |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 |
| 中文描述： | SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO24 |
| 封裝： | PLASTIC, SSOP-24 |
| 文件頁數： | 10/14頁 |
| 文件大?。?/td> | 441K |
| 代理商： | ISL6235CA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁
10
One of the parameters limiting the converter’s response to a
load transient is the time required for the inductor current to
slew to it’s new level. Given a sufficiently fast control loop
design, the ISL6235 will provide either 0% or 94% duty cycle
in response to a load transient. The response time is the
time interval required to slew the inductor current from an
initial current value to the load current level. During this
interval the difference between the inductor current and the
transient current level must be supplied by the output
capacitor(s). Minimizing the response time can minimize the
output capacitance required. Also, if the load transient rise
time is slower than the inductor response time, as in a hard
drive or CD drive, this reduces the requirement on the output
capacitor.
The maximum capacitor value required to provide the full,
rising step, transient load current during the response time of
the inductor is:
L
IN
–
Where: C
OUT
is the output capacitor(s) required, L
O
is the
output inductor, I
TRAN
is the transient load current step, V
IN
is the input voltage, V
OUT
is output voltage, and
V
OUT
is
the drop in output voltage allowed during the load transient.
High frequency capacitors initially supply the transient
current and slow the load rate-of-change seen by the bulk
capacitors. The bulk filter capacitor values are generally
determined by the ESR (Equivalent Series Resistance) and
voltage rating requirements as well as actual capacitance
requirements. The output voltage ripple is due to the
inductor ripple current and the ESR of the output capacitors
as defined by:
where,
I
L
is calculated in the Inductor Selection section.
High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load
circuitry for specific decoupling requirements.
Use only specialized low-ESR capacitors intended for
switching-regulator applications, at 300kHz, for the bulk
capacitors. In most cases, multiple electrolytic capacitors of
small case size perform better than a single large case
capacitor.
The stability requirement on the selection of the output
capacitor is that the ‘ESR zero’, f
Z
, be between 1.2kHz and
30kHz. This range is set by an internal, single compensation
zero at 6kHz. The ESR zero can be a factor of five on either
side of the internal zero and still contribute to increased
phase margin of the control loop. Therefore:
Z
In conclusion, the output capacitors must meet three criteria:
1. They must have sufficient bulk capacitance to sustain the
output voltage during a load transient while the output
inductor current is slewing to the value of the load
transient
2. The ESR must be sufficiently low to meet the desired
output voltage ripple due to the output inductor current,
and
3. The ESR zero should be placed, in a rather large range,
to provide additional phase margin.
3.3V ALWAYS and 5V ALWAYS Output Capacitors
The output capacitors for the linear regulators insure stability
and provide dynamic load current. The 3.3V ALWAYS and
the 5V ALWAYS linear regulators should have, as a
minimum, 10
μ
F capacitors on their outputs.
3.3V Main and 5V Main PWM Output Inductor
Selection
The PWM converters require output inductors. The output
inductor is selected to meet the output voltage ripple
requirements. The inductor value determines the converter’s
ripple current and the ripple voltage is a function of the ripple
current and output capacitor(s) ESR. The ripple voltage
expression is given in the capacitor selection section and the
ripple current is approximated by the following equation:
V
–
S
Input Capacitor Selection
The important parameters for the bulk input capacitor(s) are
the voltage rating and the RMS current rating. For reliable
operation, select bulk input capacitors with voltage and
current ratings above the maximum input voltage and largest
RMS current required by the circuit. The capacitor voltage
rating should be at least 1.25 times greater than the
maximum input voltage and 1.5 times is a conservative
guideline.
The ac RMS input current varies with load as shown in
Figure 4. Depending on the specifics of the input power and
it’s impedance, most (or all) of this current is supplied by the
input capacitor(s). Figure 4 also shows the advantage of
having the PWM converters operating out of phase. If the
converters were operating in phase, the combined RMS
current would be the algebraic sum, which is a much larger
value as shown. The combined out-of-phase current is the
square root of the sum of the square of the individual
reflected currents and is significantly less than the combined
in-phase current.
C
OUT
V
OUT
2
---------------------------------------------
I
OUT
--------------------
×
=
(EQ. 5)
V
RIPPLE
IL
ESR
×
=
(EQ. 6)
C
OUT
-------------------------------------------
=
(EQ. 7)
IL
V
-------------------------------
V
IN
---------------
×
=
(EQ. 8)
ISL6235
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6244CR | Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 |
| ISL6244HR-T | Test Probe; Range:-32deg to 500degF RoHS Compliant: NA |
| ISL6244HRZ | Multi-Phase PWM Controller |
| ISL6244HRZ-T | Multi-Phase PWM Controller |
| ISL6244 | Multi-Phase PWM Controller(多相PWM控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6235CA-T | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| ISL6236 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers |
| ISL6236A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers |
| ISL6236AIRZ | 功能描述:IC MAIN PWR CTRLR QUAD 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6236AIRZ-T | 功能描述:IC MAIN PWR CTRLR QUAD 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。