- 您現在的位置：買賣IC網 > PDF目錄383144 > ISL6291-1CRZ-T (INTERSIL CORP) Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6291-1CRZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-SOIC -40 to 85 |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| 封裝： | 5 X 5 MM, THERMALLY ENHANCED, PLASTIC, MO-220VHHB, QFN-16 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 357K |
| 代理商： | ISL6291-1CRZ-T |
8
FN9102.2
May 2, 2005
charge time exceeds the TIMEOUT interval, a fault is issued
and the charger is latched. The charger then enters the Fault
state.
The TIMEOUT limit is disabled when the TOEN pin is pulled
to LOW (see TOEN pin description for more information).
During the constant current charge mode, the STATUS pin
remains LOW and the FAULT pin remains HIGH.
Constant Voltage Charge Mode
The ISL6291 regulates the battery terminal voltage at V
CH
in
the constant voltage mode. As the battery continues being
charged, the charge current starts to decrease, as shown in
Figure 1. When the charge current drops to the minimum
value I
MIN
, programmed by the IMIN pin, the charge cycle
completes. The total charge time for the constant current
mode and the constant voltage mode must not exceed the
TIMEOUT interval, unless the TOEN pin is pulled LOW;
otherwise, the charger also stops charging and indicates a
FAULT status. During the constant voltage mode, the
STATUS remains LOW and the FAULT remains HIGH.
Two versions of ISL6291 (see Ordering Information) are
available: a 4.1V termination voltage version, and a 4.2V
termination voltage version.
Inhibit State
The charger enters the Inhibit State once a normal charge
cycle completes. The ISL6291 then monitors the battery
voltage. Once the battery voltage falls below the V
RECHRG
threshold, a new charge cycle starts, as shown in Figure 1.
Both STATUS and FAULT are HIGH in this state.
Fault State
Two types of fault may occur during a charge cycle: the
TIMEOUT fault (refer to the TIME pin and the TOEN pin
description), and the temperature fault (see TEMP pin
description and the Battery Pack Temperature Monitoring
section). When a TIMEOUT fault occurs, the charger is
latched. The latch is released only by recycling the input
power or toggling the EN signal. When a temperature fault
occurs, the charger is reset and a new charge cycle starts
when the temperature fault ends. In case of a fault, the
FAULT pin indicates a logic LOW and the STATUS pin
outputs a logic HIGH.
Standby State
The charger is in the Standby State when the EN pin is held
LOW or the wall adapter is removed. The charger draws less
than 1
μ
A of standby current when the adapter is removed.
Timing Diagram
Figure 2 summarizes the operation of the charger and the
key signals after an adapter is attached to the charger input.
No fault occurs in this diagram and the EN pin is assumed
not connected to logic LOW.
Internal Current Sensing
A 100,000:1 current mirror is employed to sense the current
in the pass element, as shown in the Block Diagram. The
current mirror is trimmed to 10% accuracy. The second
mirrored output, represented by I
SEN2
in the block diagram,
is used to compare with the IMIN pin current to determine
the end-of-charge condition.
Charge Current Control
The charging current in the pass element is controlled by the
current amplifier CA, as shown in the Block Diagram. The
CA, the pass element, and the 100,000:1 current mirror form
a control loop. During a trickle charge mode or a constant
current charge mode, the control reference to the loop is the
reference current I
R
. The voltage amplifier VA does not
affect the loop operation because the battery voltage is lower
than the charge termination voltage V
CH,
so that the voltage
amplifier output is blocked by the diode connecting to the
current reference. If the charge current in the PMOS pass
element is too high, its mirrored output is higher than the
reference I
R
. The non-inverting input of the current amplifier
has a higher voltage than the inverting input so that the
current amplifier output increases, reducing the gate-to-
source voltage of the PMOS pass element. The current in
the pass element thereby reduces. If the charge current is
too low, the current amplifier output reduces to force the
current to increase.
During the Trickle mode charge, the current reference
typically equals 1/10 of the current in the IREF pin. During
the constant current mode, the reference current equals the
current in the IREF pin.
If the temperature inside the IC rises above a typical value of
100°C, the current source block starts to reduce the reference
current I
R
at a rate of 0.4
μ
A/°C for every degree of
temperature rise.
FIGURE 2. TIMING DIAGRAM AFTER AN ADAPTER IS
ATTACHED TO THE CHARGER INPUT
VIN
V2P8
STATUS
FAULT
VBAT
I
CHARGE
15 Cycles to
1/8 TIMEOUT
15 Cycles
POR Threshold
200us
POR
3.0V V
MIN
V
RECHRG
t
0
t
1
t
2
t
3
t
4
t
5
t
6
t
7
t
8
Charge Cycle
Charge
Cycle
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6291-2CR | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-SOIC -40 to 85 |
| ISL6291-2CR-T | Li-ion/Li Polymer Linear Battery Charger |
| ISL6291-2CRZ | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-SOIC -40 to 85 |
| ISL6291-2CRZ-T | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-SOIC -40 to 85 |
| ISL6291EVAL1 | Li-ion/Li Polymer Linear Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL62912CR | 制造商:Intersil Corporation 功能描述: |
| ISL6291-2CR | 功能描述:IC CHARGER LI-ION 4.2V 16-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL6291-2CR-T | 功能描述:IC BATT CHRGR LI-ION 4.2V 16-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL6291-2CRTR5155 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Linear Battery Charger |
| ISL6291-2CRTR5155-T | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Linear Battery Charger |
發布緊急采購，3分鐘左右您將得到回復。