- 您現在的位置：買賣IC網 > PDF目錄383144 > ISL6292BCR-T (INTERSIL CORP) Li-ion/Li Polymer Battery Charger PDF資料下載
參數資料
| 型號： | ISL6292BCR-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Li-ion/Li Polymer Battery Charger |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| 封裝： | LEAD FREE, 4 X 4 MM, PLASTIC, QFN-16 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 287K |
| 代理商： | ISL6292BCR-T |
10
FN9139 .1
April 19, 2005
create a hysteresis for each comparator respectively. The
DT pin is shorted to GND via the internal Q3 MOSFET when
the charger is not charging, resulting in the equivalent circuit
shown in Figure 7 (A). The on-resistance of Q3 is typically
50
and is negligible compared to the external resistors.
When the charger starts to charge, Q3 is turned off to set a
higher temperature range determined by the external
resistor R
D
.
The equivalent circuit is shown in Figure 7 (B).
The DT pin allows the user to set up a higher shut down
ambient temperature after the charger starts up.
The selection of R
U
and R
T
uses the same procedure
described in the ISL6292 datasheet. The selection R
D
follows the following equation:
R
D
= R
T,@45
°
C
- R
T,@(45
°
C +
T)
where R
T,@45
°
C
is the thermistor resistance at 45°C and the
R
T,@(45
°
C +
T)
is the resistance at 45°C +
T. Figure 8
shows the temperature windows before, during, and after
charging. Before and after charging, the temperature window
is -5°C to 45°C with 5°C hysteresis. During charging, the
high temperature limit changes to 45°C +
T. If this limit is
exceeded, the charger is stopped and the temperature has
to come back to below 40°C for the charging to be allowed
again. The low temperature limit is also increased. However,
the R
D
typically has a much lower resistance than the NTC
at low temperature, therefore, the influence on the
temperature threshold is not as much as at high
temperature. Typically, the low temperature threshold is
raised by less than 2°C, as shown in Figure 8.
Charge Current Thermal Foldback
The thermal foldback function monitors the die temperature
and reduces the charge current when the die temperature
rises above 100°C to prevent further temperature rise. The
charge current reduces at a rate of 100mA/°C after
exceeding 100°C. For a charger with the constant charge
current set at 1A, the charge current is reduced to zero when
the internal temperature rises to 110°C. The actual charge
current settles between 100°C to 110°C.
Usually the charge current should not drop below I
MIN
because of the thermal foldback. For some extreme cases if
that does happen, the charger does not indicate end-of-
charge unless the battery voltage is already above the
recharge threshold.
2.9V Bias Voltage
The ISL6292B provides a 2.9V voltage for biasing the
internal control and logic circuit. This voltage is also
available for external circuits such as the NTC thermistor
circuit. The maximum allowed external load is 2mA.
EN Pin
The EN pin allows direct interface to the battery ID pin of a
battery pack. The battery ID pin is connected with a resistor
of a value less than 27k
to ground inside the battery pack.
When the battery is not attached, the EN pin is pulled up by
an internal source to the V2P9 pin to disable the charger.
The 2.9V internal regulator is on as long as the input power
is applied, independent of the EN input. Table 2 summarizes
the status of each pin when the IC is disabled.
FIGURE 7. EQUIVALENT CIRCUITS FOR THE NTC DIVIDER
(A) BEFORE CHARGING STARTS
(B) DURING CHARGING.
V2P9
TEMP
DT
R
U
R
T
R
Q3
GND
V2P9
TEMP
R
U
R
T
R
D
GND
(A)
(B)
TABLE 2. SUMMARY OF PIN BEHAVIOR WHEN THE IC IS
DISABLED BY THE EN PIN
PIN
BEHAVIOR
V2P9
Outputs 2.9V.
RED
High impedance
GRN
High impedance
DT
Low impedance
IREF
Outputs 0.8V
IMIN
Outputs 0.8V
TEMP
The temperature monitoring circuit remains functioning.
FIGURE 8. BOARD TEMPERATURE MONITORING WHEN
THE CHARGE IS NOT CHARGING, THE
TEMPERATURE WINDOW IS -5°C AND 45°C.
ONCE THE CHARGER STARTS, THE
TEMPERATURE WINDOW IS 1.X°C TO 45°C+
T.
0
o
C
-5
o
C
45
o
C
40
o
C
45
o
C +
T
Less than 2
°
C
CHARGE
NOT CHARGE
NOT CHARGE
ISL6292B
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6292B | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SSOP -40 to 85 |
| ISL6292CCR3Z-T | Li-ion/Li Polymer Battery Charger |
| ISL6292CCR3Z | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
| ISL6292DCR4 | Li-ion/Li Polymer Battery Charger |
| ISL6292D | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6292BCRZ | 功能描述:IC CHARGER LI-ION 4.2V 4X4 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6292BCRZ-T | 功能描述:IC CHARGER LI-ION POLYMER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6292C | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL6292CCR3Z | 功能描述:電池管理 VSENSE BONDED OUT RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| ISL6292CCR3Z-T | 功能描述:IC CHARGER LI-ION POLYMER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
發布緊急采購，3分鐘左右您將得到回復。