- 您現在的位置：買賣IC網 > PDF目錄383144 > ISL6292EVAL1 (Intersil Corporation) Li-ion/Li Polymer Battery Charger PDF資料下載
參數資料
| 型號： | ISL6292EVAL1 |
| 廠商： | Intersil Corporation |
| 英文描述： | Li-ion/Li Polymer Battery Charger |
| 中文描述： | Li-ion/Li聚合物電池充電器 |
| 文件頁數： | 13/19頁 |
| 文件大?。?/td> | 647K |
| 代理商： | ISL6292EVAL1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁
13
FN9105.6
July 25, 2005
As the TEMP pin voltage rises from low and exceeds the
1.4V threshold, the under temperature signal rises and does
not clear until the TEMP pin voltage falls below the 1.2V
falling threshold. Similarly, the over-temperature signal is
given when the TEMP pin voltage falls below the 0.35V
threshold and does not clear until the voltage rises above
0.406V. The actual accuracy of the 2.8V is
not important
because all the thresholds and the TEMP pin voltage are
ratios determined by the resistor dividers, as shown in
Figure 22.
The NTC thermistor is required to have a resistance ratio of
7:1 at the low and the high temperature limits, that is,
(EQ. 7)
This is because at the low temperature limit, the TEMP pin
voltage is 1.4V, which is 1/2 of the 2.8V bias. Thus,
(EQ. 8)
where R
U
is the pull-up resistor as shown in Figure 22. On
the other hand, at the high temperature limit the TEMP pin
voltage is 0.35V, 1/8 of the 2.8V bias. Therefore,
(EQ. 9)
Various NTC thermistors are available for this application.
Table 1 shows the resistance ratio and the negative
temperature coefficient of the curve-1 NTC thermistor from
Vishay (http://www.vishay.com) at various temperatures. The
resistance at 3°C is approximately seven times the
resistance at 47°C, that is:
(EQ. 10)
Therefore, if 3°C is the low temperature limit, then the high
temperature limit is approximately 47°C. The pull-up resistor
R
U
can choose the same value as the resistance at 3°C.
The temperature hysteresis can be estimated. At the low
temperature, the hysteresis is approximately,
(EQ. 11)
where 0.051 is the NTC at 3°C. Similarly, the high
temperature hysteresis is,
(EQ. 12)
where the 0.039 is the NTC at 47°C.
For applications that do not need to monitor the battery
temperature, the NTC thermistor can be replaced with a
regular resistor of
a half value of the pull up resistor
R
U
.
Another option is to connect the TEMP pin to the IREF pin
that has a 0.8V output. With such connection, the IREF pin
can no longer be programmed with logic inputs.
Battery Removal Detection
The ISL6292 assumes that the thermistor is co-packed with
the battery and is removed together with the battery. When
the charger senses a TEMP pin voltage that is 2.1V or
higher, it assumes that the battery is removed. The battery
removal detection circuit is also shown in Figure 22. When a
battery is removed, a FAULT signal is indicated and charging
is halted. When a battery is inserted again, a new charge
cycle starts.
Indications
The ISL6292 has three indications: the input presence, the
charge status, and the fault indication. The input presence is
indicated by the V2P8 pin while the other two indications are
presented by the STATUS pin and FAULT pin respectively.
Figure 23 shows the V2P8 pin voltage vs. the input voltage.
Table 2 summarizes the other two pins.
TABLE 1. RESISTANCE RATIO OF VISHAY’S CURVE-1 NTC
TEMPERATURE (°C)
R
T
/R
25°C
NTC (%/°C)
0
3.266
5.1
3
2.806
5.1
5
2.540
5.0
25
1.000
4.4
45
0.4368
4.0
47
0.4041
3.9
50
0.3602
3.9
R
HOT
-------------------
7
=
R
COLD
R
U
=
R
HOT
R
U
7
-------
=
R
-----------------
R
47oC
7
=
T
hysLOW
1.4V 0.051
-------------------------------
3
≈
≈
oC
(
)
T
hysHIGH
-------------------------------------
4
≈
≈
oC
(
)
FIGURE 23. THE V2P8 PIN OUTPUT vs THE INPUT VOLTAGE
AT THE VIN PIN. VERTICAL: 1V/DIV,
HORIZONTAL: 100ms/DIV.
3.4V
2.4V
2.8V
V
IN
V2P8
ISL6292
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6292EVAL2 | Li-ion/Li Polymer Battery Charger |
| ISL6292-1CR4Z-T | Li-ion/Li Polymer Battery Charger |
| ISL6292-2CR4Z-T | Li-ion/Li Polymer Battery Charger |
| ISL6292BCRZ-T | ECONOLINE: REZ - Cost Effective- 1kVDC & 2kVDC Isolation- Custom Solutions Available- No Extern. Components Required- UL94V-0 Package Material- Efficiency to 85% |
| ISL6292BCR-T | Li-ion/Li Polymer Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6292EVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL6292 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6292EVAL2 | 功能描述:EVALUATION BOARD 2 ISL6292 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6292EVAL2Z | 功能描述:EVALUATION BOARD FOR ISL6292 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6293 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger Accepting Two Power Sources |
| ISL6293_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger Accepting Two Power Sources |
發布緊急采購，3分鐘左右您將得到回復。