- 您現在的位置：買賣IC網 > PDF目錄383144 > ISL6299A (Intersil Corporation) Quadruple 2-Input Exclusive-OR Gates 14-SSOP -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6299A |
| 廠商： | Intersil Corporation |
| 英文描述： | Quadruple 2-Input Exclusive-OR Gates 14-SSOP -40 to 85 |
| 中文描述： | 鋰聚合物電池充電器可供兩個電源 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 222K |
| 代理商： | ISL6299A |
5
FN9212.0
June 28, 2005
Functional Pin Description
CRDL (Pin 1)
Cradle input. This pin is usually connected to a cradle power
input. The maximum input voltage is 28V. The charge
current from this pin is programmable with the ICDL pin up to
1A. When this pin is connected to a power source, no charge
current is drawn from the USB pin. A 1μF or larger value
ceramic capacitor is recommended for decoupling.
USB (Pin 2)
USB input. This pin is usually connected to a USB port
power connector. Other sources that are lower than 5.5V are
also acceptable. The charge current from the USB pin is
fixed at typically 380mA. A 1μF or larger value ceramic
capacitor is recommended for decoupling. It is also
recommended to have a 1
resistor in series with the
decoupling capacitor to prevent an over-shoot voltage when
a USB cable is plugged in.
PPR (Pin 3)
Power presence indication. An open-drain output pin which
turns ON when either the USB input voltage or the CRDL
input voltage is above its POR level, regardless if the
charger is enabled or disabled. Otherwise turns OFF. This
pin provides a wake-up signal to a microprocessor when
either the cradle or the USB power is connected.
CHG (Pin 4)
Charge indication pin. An open-drain output which turns ON
when the charge current from the cradle input is above
programmable IMIN or when the charge current from the
USB input is above the fixed end of charge current
threshold. Otherwise turns OFF.
EN (Pin 5)
Enable logic input. Connect to LOW or leave floating to
enable the charger.
IMIN (Pin 6)
IMIN is the programmable input for the end-of-charge
current. IMIN is calculated by the following equation:
Where R
IMIN
is in k
.
IMIN is only applicable to the cradle
charging. The USB EOC current has been fixed as shown on
the electrical specification table.
USBON (Pin 7)
The USBON pin is a control input to turn off the USB charge
function if desired. Connect to LOW or leave floating to turn
off USB charge.
PRECONDITIONING CHARGE THRESHOLD
Preconditioning Charge Threshold Voltage
V
MIN
2.5
2.6
2.7
V
INTERNAL TEMPERATURE MONITORING
Current Foldback Threshold (Note 7)
T
FOLD
85
100
115
°C
LOGIC INPUT AND OUTPUT
USBON Logic input High
1.3
-
-
V
USBON Logic input LOW
-
-
0.4
V
EN Pin Logic Input High
1.3
-
-
V
EN Pin Logic Input Low
-
-
0.4
V
EN Pin Internal Pull Down Resistance
-
600
-
k
USBON Pin internal Pull Down Resistance
-
1000
-
k
CHG/PPR Sink Current
Pin Voltage = 0.8V
10
-
-
mA
NOTES:
3. The 4.0V V
BAT
is selected so that the CHG output can be used as the indication for the offset comparator output indication. If the V
BAT
is lower
than the POR threshold, no output pin can be used for indication.
4. The maximum and minimum limits are guaranteed over -40°C to 70°C ambient temperature range.
5. The charge current can be affected by the thermal foldback function if the IC under the test setup cannot dissipate the heat.
6. Constant current can be affected if the junction temperature exceeds 70 °C.
7. Guaranteed by characterization or correlation to other test.
Electrical Specifications
Typical Values Are Tested at USB = CRDL = 5V and ambient temperature is at 25°C, Unless Otherwise Noted.
All Maximum and Minimum Values Are Guaranteed Under the Recommended Operating Conditions.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNITS
I
MIN
IMIN
----------------
4
mA
(
)
–
=
ISL6299A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6299AIRZ-T | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL6299IRZ | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL6299 | Quadruple 2-Input Exclusive-OR Gates 14-SSOP -40 to 85 |
| ISL6299IRZ-T | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL6308IRZ | Three-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6299A_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL6299AEVAL1 | 功能描述:EVALUATION BOARD 1 ISL6299A RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6299AIRZ | 功能描述:IC CHARGER LI-ION POLYMER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| ISL6299AIRZ-T | 功能描述:IC CHARGER LI-ION POLYMER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6299IRZ | 功能描述:IC CHARGER BATTERY LI-ION 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。