參數資料
型號： ISL6310CRZ
廠商： INTERSIL CORP
元件分類： 穩壓器
英文描述： Two-Phase Buck PWM Controller with High Current Intergrated MOSFET Driver
中文描述： SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC32
封裝： 5 X 5 MM, ROHS COMPLIANT, PLASTIC, MO-220VHHD-2, QFN-32
文件頁數： 10/27頁
文件大?。?/td> 711K
代理商： ISL6310CRZ
10
FN9209.2
October 19, 2005
Figures 25 and 26 in the section entitled
Input Capacitor
Selection
can be used to determine the input-capacitor RMS
current based on load current, duty cycle, and the number of
channels. They are provided as aids in determining the
optimal input capacitor solution.
PWM Operation
The timing of each converter leg is set by the number of
active channels. The default channel setting for the ISL6310
is two. One switching cycle is defined as the time between
the internal PWM1 pulse termination signals. The pulse
termination signal is the internally generated clock signal
that triggers the falling edge of PWM1. The cycle time of the
pulse termination signal is the inverse of the switching
frequency set by the resistor between the FS pin and
ground. Each cycle begins when the clock signal commands
PWM1 to go low. The PWM1 transition signals the internal
channel 1 MOSFET driver to turn off the channel 1 upper
MOSFET and turn on the channel 1 synchronous MOSFET.
In the default channel configuration, the PWM2 pulse
terminates 1/2 of a cycle after the PWM1 pulse.
One switching cycle for the ISL6310 is defined as the time
between consecutive PWM pulse terminations (turn-off of
the upper MOSFET on a channel). Each cycle begins when
a switching clock signal commands the upper MOSFET to
go off. The other channel’s upper MOSFET conduction is
terminated 1/2 of a cycle later.
Once a PWM pulse transitions low, it is held low for a
minimum of 1/3 cycle. This forced off time is required to
ensure an accurate current sample. Current sensing is
described in the next section. After the forced off time
expires, the PWM output is enabled. The PWM output state
is driven by the position of the error amplifier output signal,
V
COMP
, minus the current correction signal relative to the
sawtooth ramp as illustrated in Figure 3. When the modified
V
COMP
voltage crosses the sawtooth ramp, the PWM output
transitions high. The internal MOSFET driver detects the
change in state of the PWM signal and turns off the
synchronous MOSFET and turns on the upper MOSFET.
The PWM signal will remain high until the pulse termination
signal marks the beginning of the next cycle by triggering the
PWM signal low.
Single phase operation can be selected by connecting 2PH
to GND.
Channel Current Balance
One important benefit of multi-phase operation is the thermal
advantage gained by distributing the dissipated heat over
multiple devices and greater area. By doing this the designer
avoids the complexity of driving parallel MOSFETs and the
expense of using expensive heat sinks and exotic magnetic
materials.
In order to realize the thermal advantage, it is important that
each channel in a multi-phase converter be controlled to
carry about the same amount of current at any load level. To
achieve this, the currents through each channel must be
sampled every switching cycle. The sampled currents, I
n
,
from each active channel are summed together and divided
by the number of active channels. The resulting cycle
average current, I
AVG
, provides a measure of the total load-
current demand on the converter during each switching
cycle. Channel current balance is achieved by comparing
the sampled current of each channel to the cycle average
current, and making the proper adjustment to each channel
pulse width based on the error. Intersil’s patented current
balance method is illustrated in Figure 3, with error
correction for channel 1 represented. In the figure, the cycle
average current, I
AVG
, is compared with the channel 1
sample, I
1
, to create an error signal I
ER
.
The filtered error signal modifies the pulse width
commanded by V
COMP
to correct any unbalance and force
I
ER
toward zero. The same method for error signal
correction is applied to each active channel.
Current Sampling
In order to realize proper current balance, the currents in
each channel must be sampled every switching cycle. This
sampling occurs during the forced off-time, following a PWM
FIGURE 2. CHANNEL INPUT CURRENTS AND INPUT-
CAPACITOR RMS CURRENT FOR 2-PHASE
CONVERTER
Q1 D-S CURRENT
Q2 D-S CURRENT
C
IN
CURRENT
FIGURE 3. CHANNEL 1 PWM FUNCTION AND CURRENT-
BALANCE ADJUSTMENT
÷
N
I
AVG
I
2
Σ
-
+
+
-
+
-
f(s)
PWM1
I
1
V
COMP
SAWTOOTH SIGNAL
I
ER
NOTE: Channel 2 is optional.
FILTER
TO GATE
CONTROL
LOGIC
ISL6310
相關PDF資料
PDF描述
ISL6310EVAL1 Two-Phase Buck PWM Controller with High Current Intergrated MOSFET Driver
ISL6310IRZ Two-Phase Buck PWM Controller with High Current Intergrated MOSFET Driver
ISL6431A Advanced Pulse Width Modulation (PWM) Controller for Broadband Applications
ISL6431ACB Advanced Pulse Width Modulation (PWM) Controller for Broadband Applications
ISL6520A Adjustable Precision Shunt Regulator 3-SOT-23 -40 to 125
相關代理商/技術參數
參數描述
ISL6310CRZ-T 功能描述:電壓模式 PWM 控制器 W/ANNEAL 2-PH PWM CNTRLR W/2-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
ISL6310EVAL1Z 功能描述:EVALUATION BOARD FOR ISL6310 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
ISL6310IRZ 功能描述:電壓模式 PWM 控制器 W/ANNEAL 2-PH PWM CNTROL W/2-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
ISL6310IRZ-T 功能描述:電壓模式 PWM 控制器 W/ANNEAL 2-PH PWM CNTROL W/2-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
ISL6312ACRZ 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*