- 您現在的位置：買賣IC網 > PDF目錄383145 > ISL6316IRZ (INTERSIL CORP) MINIATURE TOGGLE SWITCH PDF資料下載
參數資料
| 型號： | ISL6316IRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | MINIATURE TOGGLE SWITCH |
| 中文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封裝： | 6 X 6 MM, ROHS COMPLIANT, PLASTIC, MO-220-VJJD-2, QFN-40 |
| 文件頁數： | 18/29頁 |
| 文件大?。?/td> | 838K |
| 代理商： | ISL6316IRZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
18
FN9227.0
August 31, 2005
Assuming the microprocessor controls the VID change at 1-bit
every T
VID
, the relationship between the time constant of
R
REF
and C
REF
network and T
VID
is given by Equation 13.
Operation Initialization
Prior to converter initialization, proper conditions must exist on
the enable inputs and VCC. When the conditions are met, the
controller begins soft-start. Once the output voltage is within
the proper window of operation, PGOOD asserts logic high.
Enable and Disable
While in shutdown mode, the PWM outputs are held in a high-
impedance state to assure the drivers remain off. The
following input conditions must be met before the ISL6316 is
released from shutdown mode.
1. The bias voltage applied at VCC must reach the internal
power-on reset (POR) rising threshold. Once this
threshold is reached, proper operation of all aspects of
the ISL6316 is guaranteed. Hysteresis between the rising
and falling thresholds assure that once enabled, the
ISL6316 will not inadvertently turn off unless the bias
voltage drops substantially (see
Electrical
Specifications
).
2. The ISL6316 features an enable input (EN_PWR) for
power sequencing between the controller bias voltage
and another voltage rail. The enable comparator holds
the ISL6316 in shutdown until the voltage at EN_PWR
rises above 0.875V. The enable comparator has about
130mV of hysteresis to prevent bounce. It is important
that the driver ICs reach their POR level before the
ISL6316 becomes enabled. The schematic in Figure 10
demonstrates sequencing the ISL6316 with the ISL66xx
family of Intersil MOSFET drivers, which require 12V
bias.
3. The voltage on EN_VTT must be higher than 0.875V to
enable the controller. This pin is typically connected to the
output of VTT VR.
4. The VID code must be valid and not be OFF codes. When
controller receives VID OFF code, the controller will
execute a 2-cycle delay before changing the overvoltage
trip level to the shut-down level and disabling PWM.
Overvoltage shutdown can not be reset using this code.
When all conditions above are satisfied, ISL6316 begins the
soft-start and ramps the output voltage based on the VID code
and offset voltage.
The “OFF“ VID codes (“111111” and ‘111110’) are latched. If
ISL6316 is enabled with an “OFF“ VID code present, the
regulator will be latched off and recycling the POR, EN_VTT
or EN_PWR signal is needed to restart.
Soft-start
ISL6316 based VR has 2 periods during soft-start as shown in
Figure 11. After Vcc, EN_VTT and EN_PWR reach their
POR/enable thresholds, The controller will have a fixed delay
period TD1. After this delay period, the VR will begin the first
soft-start ramp until the output voltage reaches the final
setting.
The soft-start time is the sum of the 2 periods as shown in the
following equation.
TD1 is the fixed delay with the typical value equal to 1.36ms.
During TD2, ISL6316 digitally controls the DAC voltage
change at 6.25mV per step. The time for each step is equal to
the period of the soft-start oscillator, which is defined by the
resistor Rss from SS pin to GND. The soft-start ramp time
TD2 can be calculated based on the following equation.
For example, when VID is set to 1.1V and the Rss is equal to
100k
, the soft-start ramp time TD2 will be 704μs.
C
REF
R
REF
T
VID
=
(EQ. 13)
FIGURE 10. POWER SEQUENCING USING THRESHOLD-
SENSITIVE ENABLE (EN) FUNCTION
-
+
0.875V
EXTERNAL CIRCUIT
ISL6316 INTERNAL CIRCUIT
EN_PWR
+12V
POR
CIRCUIT
10k
91
0
ENABLE
COMPARATOR
SOFT-START
AND
FAULT LOGIC
EN_VTT
VCC
+
-
0.875V
T
SS
TD1
TD2
+
=
(EQ. 14)
TD2
VIDxR
-6.25x25
μ
s
(
)
=
(EQ. 15)
ISL6316
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6316CRZ | Enhanced 4-Phase PWM Controller with 6-Bit VID Code Capable of Precision RDS(ON) or DCR Differential Current Sensing for VR10 Application |
| ISL6316CRZ-T | Quadruple 2-Input Exclusive-OR Gates 14-PDIP -40 to 85 |
| ISL6316IRZ-T | Quadruple 2-Input Exclusive-OR Gates 14-PDIP -40 to 85 |
| ISL6401 | Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs)(用戶線接口電路(SLICs)專用同步電流模式PWM) |
| ISL6401CB-T | Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6316IRZ-T | 功能描述:軟開關 PWM 控制器 W/ANNEAL ISL6306 CNTRLR INDUSTRIAL RoHS:否 制造商:Fairchild Semiconductor 輸出端數量: 輸出電流: 開關頻率: 工作電源電壓:30 V 電源電流: 最大工作溫度:+ 105 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| ISL6322CRZ | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6322CRZ-T | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6322GCRZ | 功能描述:IC CTRLR PWM BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器，DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR) |
| ISL6322GCRZ-T | 功能描述:IC CTRLR PWM BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。