- 您現在的位置：買賣IC網 > PDF目錄383145 > ISL6401 (Intersil Corporation) Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs)(用戶線接口電路(SLICs)專用同步電流模式PWM) PDF資料下載
參數資料
| 型號： | ISL6401 |
| 廠商： | Intersil Corporation |
| 英文描述： | Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs)(用戶線接口電路(SLICs)專用同步電流模式PWM) |
| 中文描述： | 同步電流模式PWM用戶線接口電路（SLIC）（用戶線接口電路（SLIC組件）專用同步電流模式脈寬調制） |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 330K |
| 代理商： | ISL6401 |
8
FN9007.7
April 13, 2005
Switching losses are the result of overlapping drain current
and source voltage at turn-off. The drain voltage begins to
rise only after the miller capacitance of the device begins to
discharge. This discharging time is a function of the external
gate resistance, Rgate and the gate-to-drain miller charge
Qgd, as shown in the following equation,
T miller = (Qgd)(R
GATE
)/(Vdd-Vth),
where Vth is the turn ON threshold voltage of the gate.
The power loss due to the external capacitance of the
MOSFET also contributes to the total switching losses,
which can be calculated as shown.
During turn on there is no overlap of drain voltage and
current because there is no current in a discontinuous
current mode converter at turn-on. Minimal losses also occur
during the off-time of the FET due to the leakage current.
P
off (time)
= (1 - D
max
)(I
leak
)(V
ds(stress)
)
Output and Input Capacitors
Output capacitors are selected based upon their value,
equivalent series resistance (ESR), equivalent series
inductance and capacitor ripple current rating. The capacitor
value controls the peak-to-peak output ripple voltage at the
switching frequency. Assuming a linear decay of the
capacitor voltage during the off time, during which the
capacitor must supply the load current, the minimum value of
the output capacitor can be calculated as follows,
Cout = [(T- T
ON(max)
)(Iout)] / Vripple),
where Vripple is the acceptable peak-to peak output voltage
ripple. However, there are practical limitations to how low a
single stage output filter can reduce the ripple voltage and
sometimes an extra LC filter stage is necessary. This second
stage filter would also reduce the output high frequency noise.
Parasitic resistance and inductance in the output capacitors
tend to make the ripple voltage much greater than expected,
based upon the above equation. Using capacitors with the
lowest possible ESR and ESL helps reduce high frequency
ripple. The rms ripple current that the output capacitors
experience is not the same as the secondary side rms output
current; it is the AC portion of it. The secondary side rms
current is in the shape of a clipped sawtooth, or trapezoid,
where the output capacitor’s current waveform is in the shape
of right triangle. Therefore, the typical capacitor ripple current
rating the output capacitor must meet is equal to,
where Ipeak (sec) is the peak-secondary current and t
RESET
is equal to the off-time of the switch. The same selection
criteria is used for the input capacitor, keeping in mind these
capacitors must also be rated to handle the maximum input
voltage.
Output Voltage
The output voltage can be set by a feedback resistor divider
network. The output is resistively divided and compared to
the reference voltage. For negative flyback output
applications, the sensed output will be fed to the NFB IN pin.
The sensed voltage in inverted, and this positive voltage is
fed to the FB- inverting input pin of the error amplifier. The
non-inverting input of the error amplifier will be a reference
voltage. So, when FB- is higher than REF voltage, the output
drivers are turned off. The opposite happens when the
resistively divided output voltage falls below the 1.24V
reference voltage.
Output Diode
The output diode in a flyback converter is subject to large
peak and rms current stresses. Schottky diodes are
recommended, because of their low forward-voltage drop and
the virtual absence of minority carrier reverse recovery. The
secondary-side Schottky rectifier was selected to meet the
working peak-reverse voltage, the peak repetitive forward-
current and the average forward-current of the application.
The working peak-reverse voltage Vrev, or blocking voltage, is
calculated according to the following equation:
V
R
= [(V
INmax
+ V
RDSon
) / N ]+ V
OUT
The reflected peak primary current constitutes the peak
repetitive forward-current through the diode. Because all
current to the output capacitors and load must flow through
the diode, the average forward diode current is equal to the
steady-state load current. Power loss in the Schottky is the
sum of the conduction losses and reverse leakage losses.
Conduction losses are calculated using the forward voltage
drop across the diode and the average forward-current.
Reverse leakage losses are dependent upon the reverse
leakage-current, the blocking voltage, and the on-time of
the FET.
Determining the Turns Ratio of the Flyback
Transformer
The turns ratio of the flyback transformer can be calculated
by using the this steady-state volt-second approach:
n = [(V
INmin
- V
DS
)(D
max
)(T)] / [(V
OUT
+ V
F
)(0.8 - D
max
)(T)]
P
switching
F
sw
C
-------------------------------------------------------
V
2
×
V
DS stress
)
I
peak primary
)
t
miller
+
+
+
=
Irms
Ipeak
(
)
------------------
4
3
)
--------------------------------
-----------------------------------------------
–
=
ISL6401
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6401CB-T | Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs) |
| ISL6401CB | Quadruple 2-Input Exclusive-OR Gates 14-SO -40 to 85 |
| ISL6401CBZ | Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs) |
| ISL6401CR | Quadruple 2-Input Exclusive-OR Gates 14-TSSOP -40 to 85 |
| ISL6401CRZ | Quadruple 2-Input Exclusive-OR Gates 14-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6401 WAF | 制造商:Intersil Corporation 功能描述: |
| ISL6401CB | 功能描述:電流型 PWM 控制器 RSLIC PWM 0/+70C 14LD RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6401CB-T | 功能描述:電流型 PWM 控制器 RSLIC PWM 0/+70C 14LD RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6401CBZ | 功能描述:IC REG CTRLR PWM CM 14-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:75 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.3 V ~ 13.5 V 降壓:是 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:0°C ~ 70°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:管件 產品目錄頁面:1051 (CN2011-ZH PDF) 其它名稱:296-2543-5 |
| ISL6401CBZ-T | 功能描述:IC REG CTRLR PWM CM 14-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。