- 您現在的位置：買賣IC網 > PDF目錄383145 > ISL6401IR (INTERSIL CORP) Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs) PDF資料下載
參數資料
| 型號： | ISL6401IR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs) |
| 中文描述： | 1 A SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | PLASTIC, MO-220VGGC, MLFP-16 |
| 文件頁數： | 5/11頁 |
| 文件大小： | 330K |
| 代理商： | ISL6401IR |
5
FN9007.7
April 13, 2005
Pin Descriptions
SD -
This pin is logic level compatible and can be pulled
high, tied to V
IN
or left open for normal operation. Logic low
on the SD activates shutdown, reducing the part’s supply
current to approximately 55
μ
A.
SYNC -
This pin is the input pin for external frequency
synchronization. The switching frequency of the device can
be synchronized by an external clock signal inserted at this
pin. The oscillator timing capacitor, C
T
, is still required, even
if an external clock is used. Program the free-running
frequency to be a minimum of 10% slower than the SYNC
input frequency.
CT -
This is the oscillator timing pin. The free-running
frequency can be set by connecting a timing capacitor to this
pin. The oscillator produces a sawtooth waveform with a
programmable frequency range of 100kHz to 1.2MHz.
Figure 4 may be used as a guideline in selecting the
capacitor value required for a given frequency.
COMP -
COMP is the output of the error amplifier and input
of the current comparator.
The ISL6401 features built-in full cycle soft-start. Soft-start is
implemented as a clamp on the maximum COMP voltage.
FB -
Feedback pin that is used for positive output voltage
sensing. It is the inverting input of the error amplifier. The
non-inverting input of the error amplifier is internally tied to a
reference voltage.
NFB-IN -
Negative feedback pin that is used for negative
output voltage sensing. It is connected to the inverting input
of the negative feedback amplifier through a 100K source
resistor.
NFB OUT -
This pin is the output of the negative feedback
inverter. This pin should be connected the FB pin with a 10K
series resistor for negative output voltage regulation
applications.
CS -
This is the input of the current sense comparator. The
IC has two different comparators: The PWM comparator and
an overcurrent comparator.
The overcurrent comparator is only intended for fault
sensing, and exceeding the overcurrent threshold will cause
a soft-start cycle.
GND -
GND is a small signal reference ground for all analog
functions on this part.
PGND -
This pin provides a dedicated ground for the output
gate driver. The GND and PGND pins should be connected
externally using a short printed circuit board trace close to
the IC. This is imperative to prevent large, high frequency
switching currents flowing through the ground metallization
inside the IC. (Decouple PV
CC
to PGND with a low ESR
0.1
μ
F capacitor.)
GATE -
This is the device output. It is a high current power
driver capable of driving the gate of a power MOSFET with
peak currents exceeding
1.0A
. This GATE output is actively
held low when V
CC
is below the UVLO threshold (3.7V typ).
The high-current power driver consists of FET output
devices, which can switch all the way to GND and all the way
to V
CC
. The output stage also provides very low impedance
to overshoot and undershoot.
PV
CC
-
This pin is for separate collector supply to the output
gate drive. Separate PV
CC
and PGnd helps decouple the
IC’s analog circuitry from the high power gate drive noise.
Connect this pin to V
CC
with external short trace on printed
circuit board.
V
CC
-
V
CC
is the power connection for the device. Although
quiescent V
CC
current is very low, total supply current will be
FIGURE 3. SUPPLY CURRENT vs TEMPERATURE
FIGURE 4. CAPACITANCE vs FREQUENCY
Typical Performance Curves
(Continued)
TEMPERATURE (
°
C)
-40
-20
25
60
85
5.0
4.0
3.0
2.0
1.0
0.5
0
C
4.5
3.5
2.5
1.5
CAPACITANCE (pF)
82
120
180
250
600
500
400
300
200
100
0
F
300
390
510
610
820
1200
ISL6401
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6401IB | PTSE 18C 18#20 SKT PLUG |
| ISL6401CR-T | Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs) |
| ISL6401CBZ-T | Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs) |
| ISL6402 | 300kHz Dual, 180° Out-of-Phase, Step-Down PWM and Single Linear Controller(300kHz雙路, 180°異相, 降壓PWM及單個線性控制器) |
| ISL6402IR-TK | 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM and Single Linear Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6401IR-T | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ISL6401IRZ | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intersil Corporation 功能描述: |
| ISL6402AEVAL4 | 功能描述:EVALUATION BOARD ISL6402A RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6402AIR | 功能描述:IC REG TRPL BCK/LINEAR 28QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6402AIR-T | 功能描述:IC REG TRPL BCK/LINEAR 28QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。