- 您現在的位置：買賣IC網 > PDF目錄383145 > ISL6402IRZ-TK (INTERSIL CORP) 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM and Single Linear Controller PDF資料下載
參數資料
| 型號： | ISL6402IRZ-TK |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM and Single Linear Controller |
| 中文描述： | DUAL SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PQCC28 |
| 封裝： | 5 X 5 MM, ROHS COMPLIANT, PLASTIC, MO-220VHHD-1, QFN-28 |
| 文件頁數： | 15/19頁 |
| 文件大?。?/td> | 422K |
| 代理商： | ISL6402IRZ-TK |
15
FN9123.3
November 8, 2004
Base-Drive Noise Reduction
The high-impedance base driver is susceptible to system
noise, especially when the linear regulator is lightly loaded.
Capacitively coupled switching noise or inductively coupled
EMI onto the base drive causes fluctuations in the base
current, which appear as noise on the linear regulator’s
output. Keep the base drive traces away from the step-down
converter, and as short as possible, to minimize noise
coupling. A resistor in series with the gate drivers reduces
the switching noise generated by PWM. Additionally, a
bypass capacitor may be placed across the base-to-emitter
resistor. This bypass capacitor, in addition to the transistor’s
input capacitor, could bring in second pole that will de-
stabilize the linear regulator. Therefore, the stability
requirements determine the maximum base-to-emitter
capacitance.
Layout Guidelines
Careful attention to layout requirements is necessary for
successful implementation of a ISL6402 based DC-DC
converter. The ISL6402 switches at a very high frequency
and therefore the switching times are very short. At these
switching frequencies, even the shortest trace has
significant impedance. Also the peak gate drive current rises
significantly in extremely short time. Transition speed of the
current from one device to another causes voltage spikes
across the interconnecting impedances and parasitic circuit
elements. These voltage spikes can degrade efficiency,
generate EMI, increase device overvoltage stress and
ringing. Careful component selection and proper PC board
layout minimizes the magnitude of these voltage spikes.
There are two sets of critical components in a DC-DC
converter using the ISL6402. The switching power
components and the small signal components. The
switching power components are the most critical from a
layout point of view because they switch a large amount of
energy so they tend to generate a large amount of noise.
The critical small signal components are those connected to
sensitive nodes or those supplying critical bias currents. A
multi-layer printed circuit board is recommended.
Layout Considerations
1. The Input capacitors, Upper FET, Lower FET, Inductor
and Output capacitor should be placed first. Isolate these
power components on the topside of the board with their
ground terminals adjacent to one another. Place the input
high frequency decoupling ceramic capacitor very close
to the MOSFETs.
2. Use separate ground planes for power ground and small
signal ground. Connect the SGND and PGND together
close of the IC. Do not connect them together anywhere
else.
3. The loop formed by Input capacitor, the top FET and the
bottom FET must be kept as small as possible.
4. Insure the current paths from the input capacitor to the
MOSFET; to the output inductor and output capacitor are
as short as possible with maximum allowable trace
widths.
5. Place The PWM controller IC close to lower FET. The
LGATE connection should be short and wide. The IC can
be best placed over a quiet ground area. Avoid switching
ground loop current in this area.
6. Place Vcc_5V bypass capacitor very close to Vcc_5V pin
of the IC and connect its ground to the PGND plane.
7. Place the gate drive components BOOT diode and BOOT
capacitors together near controller IC
8. The output capacitors should be placed as close to the
load as possible. Use short wide copper regions to
connect output capacitors to load to avoid inductance and
resistances.
9. Use copper filled polygons or wide but short trace to
connect junction of upper FET. Lower FET and output
inductor. Also keep the PHASE node connection to the IC
short. Do not unnecessary oversize the copper islands for
PHASE node. Since the phase nodes are subjected to
very high dv/dt voltages, the stray capacitor formed
between these islands and the surrounding circuitry will
tend to couple switching noise.
10. Route all high speed switching nodes away from the
control circuitry.
11. Create separate small analog ground plane near the IC.
Connect SGND pin to this plane. All small signal
grounding paths including feedback resistors, current
limit setting resistors, SYNC/SDx pull down resistors
should be connected to this SGND plane.
12. Ensure the feedback connection to output capacitor is
short and direct.
0.79
0.8
0.82
0.83
0.85
0
40
60
FEEDBACK VOLTAGE (V)
E
20
50
30
10
C
0.81
0.84
FIGURE 21. LINEAR CONTROLLER GAIN
ISL6402
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6402IV | 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM and Single Linear Controller |
| ISL6402IVZ | 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM and Single Linear Controller |
| ISL6402IR-T | 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM and Single Linear Controller |
| ISL6402IVZ-T | 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM and Single Linear Controller |
| ISL6402IVZ-TK | 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM and Single Linear Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6402IV | 功能描述:IC REG TRPL BCK/LINEAR 28TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6402IV-T | 功能描述:IC REG TRPL BCK/LINEAR 28TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6402IV-TK | 功能描述:IC REG TRPL BCK/LINEAR 28TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6402IVZ | 功能描述:IC REG TRPL BCK/LINEAR 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6402IVZ-T | 功能描述:IC REG TRPL BCK/LINEAR 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。