- 您現在的位置：買賣IC網 > PDF目錄383151 > ISL6523CB (INTERSIL CORP) Adjustable Precision Shunt Regulator 5-SOT-23 -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6523CB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Adjustable Precision Shunt Regulator 5-SOT-23 -40 to 85 |
| 中文描述： | DUAL SWITCHING CONTROLLER, 215 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | PLASTIC, MS-013AE, SOIC-28 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 498K |
| 代理商： | ISL6523CB |
12
inductor to the equivalent ESR of the output capacitor bank,
as shown in the following equation:
where
L
OUT(MIN)
- minimum output inductor value at full output
current
ESR
OUT
- equivalent ESR of the output capacitor bank
BW - desired converter bandwidth (not to exceed 0.25 to
0.30 of the switching frequency)
The design procedure for this output should follow the
following steps:
1. Choose number and type of output capacitors to meet the
output transient requirements based on the dynamic
loading characteristics of the output.
2. Determine the equivalent ESR of the output capacitor
bank and calculate minimum output inductor value.
3. Verify that chosen inductor meets this minimum value
criteria (at full output load). It is recommended the
chosen output inductor be no more than 30% saturated
at full output load.
Oscillator Synchronization
The PWM controllers use a triangle wave for comparison
with the error amplifier output to provide a pulse-width
modulated signal. Should the output voltage of the two
converters be programmed close to each other, then cross-
talk between the converters could cause non-uniform
PHASE pulse-widths and increased output voltage ripple.
The ISL6523 avoids this problem by synchronizing the two
converters 180
o
out of phase.
Component Selection Guidelines
Output Capacitor Selection
The output capacitors for each output have unique
requirements. In general the output capacitors should be
selected to meet the dynamic regulation requirements.
Additionally, the PWM converters require an output capacitor
to filter the current ripple. The load transient for the
microprocessor core requires high quality capacitors to
supply the high slew rate (di/dt) current demands.
PWM Output Capacitors
Modern microprocessors produce transient load rates
above 1A/ns. High frequency capacitors initially supply the
transient current and slow the load rate-of-change seen by
the bulk capacitors. The bulk filter capacitor values are
generally determined by the ESR (effective series
resistance) and voltage rating requirements rather than
actual capacitance requirements.
High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load on
specific decoupling requirements.
Use only specialized low-ESR capacitors intended for
switching-regulator applications for the bulk capacitors. The
bulk capacitor’s ESR determines the output ripple voltage and
the initial voltage drop following a high slew-rate transient’s
edge. An aluminum electrolytic capacitor’s ESR value is
related to the case size with lower ESR available in larger
case sizes. However, the equivalent series inductance (ESL)
of these capacitors increases with case size and can reduce
the usefulness of the capacitor to high slew-rate transient
loading. Unfortunately, ESL is not a specified parameter. Work
with your capacitor supplier and measure the capacitor’s
impedance with frequency to select a suitable component. In
most cases, multiple electrolytic capacitors of small case size
perform better than a single large case capacitor.
Linear Output Capacitors
The output capacitors for the linear regulators provide
dynamic load current. Thus capacitors C
OUT3
and C
OUT4
should be selected for transient load regulation.
PWM Output Inductor Selection
Each PWM converter requires an output inductor. The output
inductor is selected to meet the output voltage ripple
requirements and sets the converter’s response time to a
load transient. Additionally, PWM2 output inductor has to
meet the minimum value criteria for loop stability as
described in paragraph ‘
PWM2 Controller Feedback
Compensation
’. The inductor value determines the
converter’s ripple current and the ripple voltage is a function
of the ripple current. The ripple voltage and current are
approximated by the following equations:
Increasing the value of inductance reduces the ripple current
and voltage. However, large inductance values increase the
converter’s response time to a load transient.
One of the parameters limiting the converter’s response to a
load transient is the time required to change the inductor
current. Given a sufficiently fast control loop design, the
ISL6523 will provide either 0% or 100% duty cycle in
response to a load transient. The response time is the time
interval required to slew the inductor current from an initial
current value to the post-transient current level. During this
interval the difference between the inductor current and the
L
OUT MIN
)
ESR
10
1.75
×
------------------------------------------------
=
I
V
-------------------------------
V
–
S
V
IN
---------------
×
=
V
OUT
I
ESR
×
=
ISL6523
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6523CBZ | Adjustable Precision Shunt Regulator 5-SOT-23 -40 to 85 |
| ISL6523CBZ-T | VRM8.5 Dual PWM and Dual Linear Power System Controller |
| ISL6523CB-T | Label Printer; Leaded Process Compatible:Yes |
| ISL6523EVAL1 | VRM8.5 Dual PWM and Dual Linear Power System Controller |
| ISL6524A | Adjustable Precision Shunt Regulator 3-SOT-23 -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6523CB-T | 功能描述:IC CTRLR VRM8.5 PWM DUAL 28-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6523CBZ | 功能描述:IC CTRLR VRM8.5 PWM DUAL 28-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6523CBZ-T | 功能描述:IC CTRLR VRM8.5 PWM DUAL 28-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6523EVAL1 | 功能描述:EVALUATION BOARD VRM8.5 ISL6523 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6524ACB | 功能描述:IC CTRLR VRM8.5 PWM TRPL 28-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。