- 您現在的位置：買賣IC網 > PDF目錄383153 > ISL6527ACR-T (INTERSIL CORP) Adjustable Precision Shunt Regulator 3-SOT-23 -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6527ACR-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Adjustable Precision Shunt Regulator 3-SOT-23 -40 to 85 |
| 中文描述： | SWITCHING CONTROLLER, 645 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | 5 X 5 MM, PLASTIC, MO-220VHHB, QFN-16 |
| 文件頁數： | 8/14頁 |
| 文件大小： | 403K |
| 代理商： | ISL6527ACR-T |
8
FN9056.7
April 8, 2005
Overcurrent Protection
The overcurrent function protects the converter from a shorted
output by using the upper MOSFET on-resistance, r
DS(ON)
, to
monitor the current. This method enhances the converter’s
efficiency and reduces cost by eliminating a current sensing
resistor.
The overcurrent function cycles the soft-start function in a
hiccup mode to provide fault protection. A resistor (R
OCSET
)
programs the overcurrent trip level (see Typical Application
diagrams on pages 2 and 3). An internal 20
μ
A (typical) current
sink develops a voltage across R
OCSET
that is referenced to
V
IN
. When the voltage across the upper MOSFET (also
referenced to V
IN
) exceeds the voltage across R
OCSET
, the
overcurrent function initiates a soft-start sequence.
Figure 3 illustrates the protection feature responding to an
overcurrent event. At time T0, an overcurrent condition is
sensed across the upper MOSFET. As a result, the regulator
is quickly shutdown and the internal soft-start function begins
producing soft-start ramps. The delay interval seen by the
output is equivalent to three soft-start cycles. The fourth
internal soft-start cycle initiates a normal soft-start ramp of the
output, at time t1. The output is brought back into regulation
by time t2, as long as the overcurrent event has cleared..
Had the cause of the overcurrent still been present after the
delay interval, the overcurrent condition would be sensed
and the regulator would be shut down again for another
delay interval of three soft-start cycles. The resulting hiccup
mode style of protection would continue to repeat indefinitely
The overcurrent function will trip at a peak inductor current
(I
PEAK)
determined by:
I
x R
DS ON
)
where I
OCSET
is the internal OCSET current source (20
μ
A
typical). The OC trip point varies mainly due to the MOSFET
r
DS(ON)
variations. To avoid overcurrent tripping in the normal
operating load range, find the R
OCSET
resistor from the
equation above with:
1. The maximum r
DS(ON)
at the highest junction
temperature.
2. The minimum I
OCSET
from the specification table.
I
PEAK
3. Determine I
PEAK
for
where
I is the output inductor ripple current.
,
For an equation for the ripple current see the section under
component guidelines titled
Output Inductor Selection
.
A small ceramic capacitor should be placed in parallel with
R
OCSET
to smooth the voltage across
R
OCSET
in the
presence of switching noise on the input voltage.
Current Sinking
The ISL6527 incorporates a MOSFET shoot-through
protection method which allows a converter to sink current
as well as source current. Care should be exercised when
designing a converter with the ISL6527 when it is known that
the converter may sink current.
When the converter is sinking current, it is behaving as a
boost converter that is regulating its input voltage. This
means that the converter is boosting current into the input
rail of the regulator. If there is nowhere for this current to go,
such as to other distributed loads on the rail or through a
voltage limiting protection device, the capacitance on this rail
will absorb the current. This situation will allow the voltage
level of the input rail to increase. If the voltage level of the rail
is boosted to a level that exceeds the maximum voltage
rating of any components attached to the input rail, then
those components may experience an irreversible failure or
experience stress that may shorten their lifespan. Ensuring
that there is a path for the current to flow other than the
capacitance on the rail will prevent this failure mode.
External Reference
The ISL6527 allows the designer to determine the reference
voltage that is used. This allows the ISL6527 to be used in
many specialized applications, such as the V
TT
termination
voltage in a DDR Memory power supply, which must track
the V
DDQ
voltage by 50%. Care must be taken to insure that
this voltage does not exceed 1.5V.
FIGURE 3. OVERCURRENT PROTECTION RESPONSE
0V
TIME
VOUT (2.5V)
T1
T0
T2
INTERNAL SOFT-START FUNCTION
DELAY INTERVAL
I
PEAK
----------------------------------------------------
=
I
OUT MAX
)
I
2
----------
)
+
>
ISL6527
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6527ACRZ | Adjustable Precision Shunt Regulator 3-SOT-23 -40 to 85 |
| ISL6527ACRZ-T | Adjustable Precision Shunt Regulator 3-SOT-23 -40 to 85 |
| ISL6527AIR | Adjustable Precision Shunt Regulator 3-SOT-23 -40 to 85 |
| ISL6527AIRZ | Adjustable Precision Shunt Regulator 3-SOT-89 -40 to 85 |
| ISL6527CB | Adjustable Precision Shunt Regulator 3-SOT-89 -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6527ACRZ | 功能描述:IC REG CTRLR BST PWM VM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6527ACRZ-T | 功能描述:IC REG CTRLR BST PWM VM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6527AEVAL1 | 功能描述:EVALUATION BOARD SOIC ISL6527A RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6527AEVAL2 | 功能描述:EVALUATION BOARD QFN ISL6527A RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6527AIB | 功能描述:IC REG CTRLR BST PWM VM 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。