- 您現在的位置：買賣IC網 > PDF目錄353714 > ISL6537ACR-T (INTERSIL CORP) PWM Control Circuit 16-PDIP -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6537ACR-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | PWM Control Circuit 16-PDIP -40 to 85 |
| 中文描述： | 3.3 A DUAL SWITCHING CONTROLLER, 280 kHz SWITCHING FREQ-MAX, PQCC28 |
| 封裝： | 6 X 6 MM, PLASTIC, MO-220-VJJC, QFN-28 |
| 文件頁數： | 15/15頁 |
| 文件大?。?/td> | 488K |
| 代理商： | ISL6537ACR-T |
9
FN9143.3
internal resistors and the VREF_IN capacitor will determine
the rise time of the VTT_DDR regulator (see the Functional
Pin Description section for proper sizing of the VREF_IN
capacitor).
At time t6, a full soft-start cycle has passed from the time that
the VTT_DDR regulator was enabled. At this time the
VIDPGD comparator is enabled. Once enabled if the
VTT_GMCH/CPU output is within regulation, the VIDPGD pin
will be forced to a high impedance state.
Active to Sleep (S0 to S3 Transition)
When SLP_S3 goes LOW with SLP_S5 still HIGH, the
ISL6537A will disable all the regulators except for the VDDQ
regulator, which is continually supplied by the 5VDUAL rail.
VIDPGD will also transition LOW. When VTT is disabled, the
internal reference for the VTT regulator is internally shorted
to the VTT rail. This allows the VTT rail to float. When
floating, the voltage on the VTT rail will depend on the
leakage characteristics of the memory and MCH I/O pins. It
is important to note that the VTT rail may not bleed down to
0V. Figure 1 shows how the individual regulators are
affected by the S3 state at time t7.
Sleep to Active (S3 to S0 Transition)
When SLP_S3 transitions from LOW to HIGH with SLP_S5
held HIGH and after the 12V rail exceeds POR, the
ISL6537A will initiate the soft-start sequence. This sequence
is very similar to the mechanical start soft-start sequencing.
The transition from S3 to S0 is represented in Figure 1
between times t8 and t14.
At time t8, the SLP_S3 signal transitions HIGH. This enables
the ATX, which brings up the 12V rail. At time t9, the 12V rail
has exceeded the POR threshold and the ISL6537A enters a
reset mode that lasts for 3 soft-start cycles. At time t10, the 3
soft-start cycle reset is ended and the individual regulators
are enabled and soft-started in the same sequence as the
mechanical cold start sequence, with the exception that the
VDDQ regulator is already enabled and in regulation.
Active to Shutdown (S0 to S5 Transition)
When the system transitions from active, S0, state to
shutdown, S4/S5, state, the ISL6537A IC disables all
regulators and forces the VIDPGD pin LOW. This transition
is represented on Figure 1 at time t15.
Fault Protection
The ISL6537A monitors the VDDQ regulator for under and
overvoltage events. The VDDQ regulator also has overcurrent
protection. The internal VTT_DDR LDO regulator is monitored
for under and overvoltage events. All other regulators, with the
exception of the DAC LDO, are monitored for undervoltage
events.
An overvoltage event on either the VDDQ or VTT_DDR
regulator will cause an immediate shutdown of all regulators.
This can only be cleared by toggling the SLP_S5 signal such
that the system enters the S5 sleep state and then
transitions back to the active, S0, state.
If a regulator experiences any other fault condition (an
undervoltage or an overcurrent on VDDQ), then that
regulator, and only that regulator, will be disabled and an
internal fault counter will be incremented by 1. If the disabled
regulator is used as the input for another regulator, then that
cascoded regulator will also experience a fault condition due
to a loss of input. The cascoded regulator will be disabled
and the fault counter incremented by 1.
At every fault occurrence, the internal fault counter is
incremented by 1 and an internal Fault Reset Counter is
cleared to zero. The Fault Reset Counter will increment once
for every clock cycle (1 clock cycle is typically 1/250kHz, or
4
s). If the Fault Reset Counter reaches a count of 16384
before another fault occurs, then the Fault Counter is
cleared to 0. If a fault occurs prior to the Fault Reset Counter
reaching a count of 16384, then the Fault Reset Counter is
set back to zero.
The ISL6537A will immediately shut down when the Fault
Counter reaches a count of 4 when the system is restarting
from an S5 state into the active, or S0, state. The ISL6537A
will immediately shut down when the Fault Counter reaches
a count of 5 at any other time.
The 16384 counts that are required to reset the Fault Reset
Counter represent 8 soft-start cycles, as one soft-start cycle is
2048 clock cycles. This allows the ISL6537A to attempt at least
one full soft-start sequence to restart the faulted regulators.
When attempting to restart a faulted regulator, the ISL6537A
will follow the preset start up sequencing. If a regulator is
already in regulation, then it will not be affected by the start
up sequencing.
VDDQ Overcurrent Protection
The overcurrent function protects the switching converter from
a shorted output by using the upper MOSFET on-resistance,
rDS(ON), to monitor the current. This method enhances the
converter’s efficiency and reduces cost by eliminating a
current sensing resistor.
The overcurrent function cycles the soft-start function in a
hiccup mode to provide fault protection. A resistor (ROCSET)
programs the overcurrent trip level (see Typical Application
diagrams on page 3). An internal 20
A (typical) current sink
develops a voltage across ROCSET that is referenced to the
converter input voltage. When the voltage across the upper
MOSFET (also referenced to the converter input voltage)
exceeds the voltage across ROCSET, the overcurrent function
initiates a soft-start sequence. The initiation of soft-start may
affect other regulators. The VTT_DDR regulator is directly
affected as it receives its reference and input from VDDQ.
ISL6537A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6537ACRZ | PWM Control Circuit 16-PDIP -40 to 85 |
| ISL6537ACRZ-T | ACPI Regulator/Controller for Dual Channel DDR Memory Systems |
| ISL4260EIR-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ISL4270EIR-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ISL6410IUZ-T | Single Synchronous Buck Regulators with Integrated FET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6537ACRZ | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6537ACRZR5160 | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6537ACRZ-T | 功能描述:IC REG/CTLR ACPI DUAL DDR 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
| ISL6537ACRZ-TR5160 | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6537CR | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。