- 您現在的位置：買賣IC網 > PDF目錄383155 > ISL6545ACRZ (INTERSIL CORP) 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller PDF資料下載
參數資料
| 型號： | ISL6545ACRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| 中文描述： | SWITCHING CONTROLLER, 660 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | 3 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229WEED-3, DFN-10 |
| 文件頁數： | 5/16頁 |
| 文件大小： | 302K |
| 代理商： | ISL6545ACRZ |
www.DataSheet4U.com
5
FN6305.3
November 15, 2006
Functional Pin Description (SOIC,DFN)
VCC (SOIC Pin 5, DFN Pin 6)
This pin provides the bias supply for the ISL6545, as well as
the lower MOSFET’s gate, and the BOOT voltage for the
upper MOSFET’s gate. An internal 5V regulator will supply
bias if V
CC
rises above 6.5V (but the LGATE/OCSET and
BOOT will still be sourced by VCC). Connect a well-
decoupled 5V or 12V supply to this pin.
FB (SOIC Pin 6, DFN Pin 8)
This pin is the inverting input of the internal error amplifier. Use
FB, in combination with the COMP/SD pin, to compensate the
voltage-control feedback loop of the converter. A resistor divider
from the output to GND is used to set the regulation voltage.
GND (SOIC Pin 3, DFN Pin 4)
This pin represents the signal and power ground for the IC.
Tie this pin to the ground island/plane through the lowest
impedance connection available. For the DFN package, Pin
4 MUST be connected for electrical GND; the metal pad
under the package should also be connected to the GND
plane for thermal conductivity.
PHASE (SOIC Pin 8, DFN Pin 10)
Connect this pin to the source of the upper MOSFET, and
the drain of the lower MOSFET. It is used as the sink for the
UGATE driver, and to monitor the voltage drop across the
lower MOSFET for overcurrent protection. This pin is also
monitored by the adaptive shoot-through protection circuitry
to determine when the upper MOSFET has turned off.
UGATE (SOIC Pin 2, DFN Pin 2)
Connect this pin to the gate of upper MOSFET; it provides
the PWM-controlled gate drive. It is also monitored by the
adaptive shoot-through protection circuitry to determine
when the upper MOSFET has turned off.
BOOT (SOIC Pin 1, DFN Pin 1)
This pin provides ground referenced bias voltage to the upper
MOSFET driver. A bootstrap circuit is used to create a voltage
suitable to drive an N-channel MOSFET (equal to V
CC
minus
the on-chip BOOT diode voltage drop), with respect to PHASE.
COMP/SD (SOIC Pin 7, DFN Pin 9)
This is a multiplexed pin. During soft-start and normal converter
operation, this pin represents the output of the error amplifier.
Use COMP/SD, in combination with the FB pin, to compensate
the voltage-control feedback loop of the converter.
Pulling COMP/SD low (V
DISABLE
= 0.4V nominal) will
shut-down (disable) the controller, which causes the
oscillator to stop, the LGATE and UGATE outputs to be held
low, and the soft-start circuitry to re-arm. The external pull-
down device will initially need to overcome up to 5mA of
COMP/SD output current. However, once the IC is disabled,
the COMP output will also be disabled, so only a 20μA
current source will continue to draw current.
When the pull-down device is released, the COMP/SD pin
will start to rise, at a rate determined by the 20μA charging
up the capacitance on the COMP/SD pin. When the
COMP/SD pin rises above the V
DISABLE
trip point, the
ISL6545 will begin a new Initialization and soft-start cycle.
LGATE/OCSET (SOIC Pin 4, DFN Pin 5)
Connect this pin to the gate of the lower MOSFET; it provides
the PWM-controlled gate drive (from V
CC
). This pin is also
monitored by the adaptive shoot-through protection circuitry to
determine when the lower MOSFET has turned off.
During a short period of time following Power-On Reset
(POR) or shut-down release, this pin is also used to
determine the overcurrent threshold of the converter.
Connect a resistor (R
OCSET
) from this pin to GND. See the
Overcurrent Protection
section for equations. An
overcurrent trip cycles the soft-start function, after two
dummy soft-start time-outs. Some of the text describing the
LGATE function may leave off the OCSET part of the name,
when it is not relevant to the discussion.
N/C (DFN only; Pin 3, Pin 7)
These two pins in the DFN package are No Connect.
Lower Gate Sink Impedance
R
LG-SNKh
R
UG-SRCl
R
UG-SNKl
R
LG-SRCl
R
LG-SNKl
V
CC
= 14.5V; I = 50mA
V
CC
= 4.25V; I = 50mA
V
CC
= 4.25V; I = 50mA
V
CC
= 4.25V; I = 50mA
V
CC
= 4.25V; I = 50mA
-
2.0
-
Ω
Upper Gate Source Impedance
-
3.5
-
Ω
Upper Gate Sink Impedance
-
2.7
-
Ω
Lower Gate Source Impedance
-
2.75
-
Ω
Lower Gate Sink Impedance
-
2.1
-
Ω
PROTECTION/DISABLE
OCSET Current Source
I
OCSET
ISL6545C; LGATE/OCSET = 0V
19.5
21.5
23.5
μ
A
ISL6545I; LGATE/OCSET = 0V
18.0
21.5
23.5
μ
A
Disable Threshold (COMP/SD pin)
V
DISABLE
0.375
0.400
0.425
V
Electrical Specifications
Test Conditions: V
CC
= 12V, T
J
= 0 to 85°C, Unless Otherwise Noted.
(Continued)
SYMBOL
TEST CONDITIONS
PARAMETER
MIN
TYP
MAX
UNITS
ISL6545, ISL6545A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6545AEVAL1 | 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6545AIBZ | 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6545AIRZ | 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6545CBZ | 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6545CRZ | 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6545ACRZ-T | 功能描述:IC REG CTRLR BST PWM VM 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6545AIBZ | 功能描述:IC REG CTRLR BST PWM VM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6545AIBZ-T | 功能描述:IC REG CTRLR BST PWM VM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6545AIRZ | 功能描述:IC REG CTRLR BST PWM VM 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6545AIRZ-T | 功能描述:IC REG CTRLR BST PWM VM 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。