- 您現在的位置：買賣IC網 > PDF目錄383156 > ISL6554CB-T (INTERSIL CORP) Microprocessor CORE Voltage Regulator Using Multi-Phase Buck PWM Control Without Programmable Droop PDF資料下載
參數資料
| 型號： | ISL6554CB-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Microprocessor CORE Voltage Regulator Using Multi-Phase Buck PWM Control Without Programmable Droop |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | PLASTIC, MS-013-AC, SOIC-20 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 492K |
| 代理商： | ISL6554CB-T |
9
FN9003.3
February 11, 2005
Note that Figure 5 shows the 12V gate driver voltage
available before the 5V supply to the ISL6554 has reached
its threshold level. If conditions were reversed and the 5V
supply was to rise first, the start-up sequence would be
different. In this case the ISL6554 will sense an overcurrent
condition due to charging the output capacitors. The supply
will then restart and go through the normal soft-start cycle.
Fault Protection
The ISL6554 protects the microprocessor and the entire
power system from damaging stress levels. Within the
ISL6554 both Overvoltage and Overcurrent circuits are
incorporated to protect the load and regulator.
Overvoltage
The VSEN pin is connected to the microprocessor CORE
voltage. A CORE overvoltage condition is detected when the
VSEN pin goes more than 15% above the programmed VID
level.
The overvoltage condition is latched, disabling normal PWM
operation, and causing PGOOD to go low. The latch can
only be reset by lowering and returning VCC high to initiate a
POR and soft-start sequence.
During a latched overvoltage, the PWM outputs will be driven
either low or three state, depending upon the VSEN input.
PWM outputs are driven low when the VSEN pin detects that
the CORE voltage is 15% above the programmed VID level.
This condition drives the PWM outputs low, resulting in the
lower or synchronous rectifier MOSFETs to conduct and shunt
the CORE voltage to ground to protect the load.
If after this event, the CORE voltage falls below the over-
voltage limit (plus some hysteresis), the PWM outputs will
three state. The HIP6601 family drivers pass the three-state
information along, and shuts off both upper and lower
MOSFETs. This prevents “dumping” of the output capacitors
back through the lower MOSFETs, avoiding a possibly
destructive ringing of the capacitors and output inductors. If
the conditions that caused the overvoltage still persist, the
PWM outputs will be cycled between three state and V
CORE
clamped to ground, as a hysteretic shunt regulator.
Undervoltage
The VSEN pin also detects when the CORE voltage falls
more than 9% below the VID programmed level. This causes
PGOOD to go low, but has no other effect on operation and
is not latched. There is also hysteresis in this detection point.
Overcurrent
In the event of an overcurrent condition, the overcurrent
protection circuit reduces the RMS current delivered to 41%
of the current limit. When an overcurrent condition is
detected, the controller forces all PWM outputs into a three
state mode. This condition results in the gate driver
removing drive to the output stages. The ISL6554 goes into
a wait delay timing cycle that is equal to the soft-start ramp
PWM 1
OUTPUT
PGOOD
V
CORE
5V
VCC
V
IN
= 12V
DELAY TIME
FIGURE 3. START-UP OF 4 PHASE SYSTEM OPERATING AT
500kHz
PGOOD
V
CORE
5V
VCC
V COMP
V
IN
= 12V
DELAY TIME
FIGURE 4. START-UP OF 4 PHASE SYSTEM OPERATING AT
200kHz
12V ATX
SUPPLY
PGOOD
5 V ATX
SUPPLY
V
CORE
ATX SUPPLY ACTIVATED BY ATX “PS-ON PIN”
V
IN
= 5V, CORE LOAD CURRENT = 31A
FREQUENCY 200kHz
FIGURE 5. SUPPLY POWERED BY ATX SUPPLY
ISL6554
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6554CB | Microprocessor CORE Voltage Regulator Using Multi-Phase Buck PWM Control Without Programmable Droop |
| ISL6554CBZ | Microprocessor CORE Voltage Regulator Using Multi-Phase Buck PWM Control Without Programmable Droop |
| ISL6554CBZA | Microprocessor CORE Voltage Regulator Using Multi-Phase Buck PWM Control Without Programmable Droop |
| ISL6554CBZA-T | Microprocessor CORE Voltage Regulator Using Multi-Phase Buck PWM Control Without Programmable Droop |
| ISL6554CBZ-T | Microprocessor CORE Voltage Regulator Using Multi-Phase Buck PWM Control Without Programmable Droop |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6554CB-TR5165 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6554CBZ | 功能描述:IC PWM CORE VOLTAGE REG 20-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6554CBZA | 功能描述:IC PWM CORE VOLTAGE REG 20-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6554CBZA-T | 功能描述:IC PWM CORE VOLTAGE REG 20-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6554CBZ-T | 功能描述:IC PWM CORE VOLTAGE REG 20-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。