- 您現在的位置：買賣IC網 > PDF目錄383156 > ISL6556A (Intersil Corporation) Optimized Multi-Phase PWM Controller with 6-Bit DAC for VR10.X Application PDF資料下載
參數資料
| 型號： | ISL6556A |
| 廠商： | Intersil Corporation |
| 英文描述： | Optimized Multi-Phase PWM Controller with 6-Bit DAC for VR10.X Application |
| 中文描述： | 優化的多相位6位DAC的VR10.X PWM控制器的應用 |
| 文件頁數： | 16/24頁 |
| 文件大小： | 702K |
| 代理商： | ISL6556A |
16
Soft-Start
During soft start, the DAC voltage ramps linearly from zero to
the programmed VID level. The PWM signals remain in the
high-impedance state until the controller detects that the
ramping DAC level has reached the output-voltage level.
This protects the system against the large, negative inductor
currents that would otherwise occur when starting with a pre-
existing charge on the output as the controller attempted to
regulate to zero volts at the beginning of the soft-start cycle.
The soft-start time, t
SS
, begins with a delay period equal to
64 switching cycles followed by a linear ramp with a rate
determined by the switching period, 1/f
SW
.
f
SW
For example, a regulator with 250kHz switching frequency
having VID set to 1.35V has t
SS
equal to 6.912ms.
A 100mV offset exists on the remote-sense amplifier at the
beginning of soft start and ramps to zero during the first 640
cycles of soft start (704 cycles following enable). This
prevents the large inrush current that would otherwise occur
should the output voltage start out with a slight negative
bias.
During the first 640 cycles of soft start (704 cycles following
enable) the DAC voltage increments the reference in 25mV
steps. The remainder of soft start sees the DAC ramping
with 12.5mV steps.
Fault Monitoring and Protection
The ISL6556A actively monitors output voltage and current
to detect fault conditions. Fault monitors trigger protective
measures to prevent damage to a microprocessor load. One
common power good indicator is provided for linking to
external system monitors. The schematic in Figure 10
outlines the interaction between the fault monitors and the
power good signal.
Power Good Signal
The power good pin (PGOOD) is an open-drain logic output
that transitions high when the converter is operating after
soft start.
PGOOD pulls low during shutdown and releases high after
a successful soft start. PGOOD only transitions low when an
undervoltage condition is detected or the controller is
disabled by a reset from EN, ENLL, POR, or one of the
no-CPU VID codes. After an undervoltage event, PGOOD
will return high unless the controller has been disabled.
PGOOD does not automatically transition low upon
detection of an overvoltage condition.
Undervoltage Detection
The undervoltage threshold is set at 75% of the VID code.
When the output voltage at VSEN is below the undervoltage
threshold, PGOOD gets pulled low.
Overvoltage Protection
When VCC is above 1.4V, but otherwise not valid as defined
under
Power on Reset
in
Electrical Specifications
, the
overvoltage trip circuit is active using auxiliary circuitry. In
this state, an overvoltage trip occurs if the voltage at VSEN
exceeds 1.8V.
With valid VCC, the overvoltage circuit is sensitive to the
voltage at VDIFF. In this state, the trip level is 1.7V prior to
valid enable conditions being met as described in
Enable
and Disable
. The only exception to this is when the IC has
been disabled by an overvoltage trip. In that case the
overvoltage trip point is VID plus 200mV. During soft start,
the overvoltage trip level is the higher of 1.7V or VID plus
200mV. Upon successful soft start, the overvoltage trip level
is 200mV above VID. Two actions are taken by the
t
SS
--------+
=
(EQ. 10)
FIGURE 9. SOFT-START WAVEFORMS WITH AN UN-BIASED
OUTPUT. FSW = 500kHz
VOUT, 500mV/DIV
EN, 5V/DIV
2ms/DIV
500
μ
s/DIV
FIGURE 10. POWER GOOD AND PROTECTION CIRCUITRY
OVP
-
+
VID + 0.2V
VDIFF
-
+
100
μ
A
I
AVG
-
+
DAC
REFERENCE
OV
OC
UV
PGOOD
75%
SOFT START, FAULT
AND CONTROL LOGIC
-
+
OC
I
1
REPEAT FOR
EACH CHANNEL
100
μ
A
ISL6556A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6556ACB | PWM Controller with Wide Input Range 8-SO -25 to 85 |
| ISL6556ACBZ | PWM Controller with Wide Input Range 8-SOIC -40 to 85 |
| ISL6556ACR | Optimized Multi-Phase PWM Controller with 6-Bit DAC for VR10.X Application |
| ISL6556ACR-T | Optimized Multi-Phase PWM Controller with 6-Bit DAC for VR10.X Application |
| ISL6556ACRZ | Optimized Multi-Phase PWM Controller with 6-Bit DAC for VR10.X Application |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6556ACB | 功能描述:IC CTRLR MULTIPHASE VRM10 28SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6556ACBR5208 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6556ACB-T | 功能描述:IC CTRLR MULTIPHASE VRM10 28SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6556ACBZ | 功能描述:IC CTRLR MULTIPHASE VRM10 28SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6556ACBZ-T | 功能描述:IC CTRLR MULTIPHASE VRM10 28SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。