- 您現在的位置：買賣IC網 > PDF目錄383156 > ISL6556ACRZ-T (INTERSIL CORP) PWM Controller with Wide Input Range 8-PDIP -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6556ACRZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | PWM Controller with Wide Input Range 8-PDIP -40 to 85 |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC32 |
| 封裝： | 5 X 5 MM, ROHS COMPLIANT, PLASTIC, MO-220VHHD-2, QFN-32 |
| 文件頁數： | 15/24頁 |
| 文件大?。?/td> | 702K |
| 代理商： | ISL6556ACRZ-T |
15
Dynamic VID
Modern microprocessors need to make changes to their
core voltage as part of normal operation. They direct the
core-voltage regulator to do this by making changes to the
VID inputs during regulator operation. The power
management solution is required to monitor the DAC inputs
and respond to on-the-fly VID changes in a controlled
manner. Supervising the safe output voltage transition within
the DAC range of the processor without discontinuity or
disruption is a necessary function of the core-voltage
regulator.
The ISL6556A checks the VID inputs six times every
switching cycle. If the VID code is found to have changed,
the controller waits half of a complete cycle before executing
a 12.5mV change. If during the half-cycle wait period, the
difference between DAC level and the new VID code
changes sign, no change is made. If the VID code is more
than 1 bit higher or lower than the DAC (not recommended),
the controller will execute 12.5mV changes six times per
cycle until VID and DAC are equal. It is for this reason that it
is important to carefully control the rate of VID stepping in 1-
bit increments.
In order to ensure the smooth transition of output voltage
during VID change, a VID step change smoothing network
composed of R
REF
and C
REF
is required for an ISL6556A
based voltage regulator. The selection of R
REF
is based on
the desired offset as detailed above in
Output-Voltage Offset
Programming
. The selection of C
REF
is based on the time
duration for 1 bit VID change and the allowable delay time.
Assuming the microprocessor controls the VID change at 1
bit every T
VID
, the relationship between the time constant of
R
REF
and C
REF
network and T
VID
is given by Equation 9.
Typically R
REF
is selected to be 1k
, so with a VID step
change rate of 5
μ
s per bit, the value of C
REF
is 22nF based
on Equation 9.
Initialization
Prior to initialization, proper conditions must exist on the
enable inputs and VCC. When the conditions are met, the
controller begins soft-start. Once the output voltage is within
the proper window of operation, PGOOD asserts logic 1.
Enable and Disable
While in shutdown mode, the PWM outputs are held in a
high-impedance state to assure the drivers remain off. The
following input conditions must be met before the ISL6556A
is released from shutdown mode.
1. The bias voltage applied at VCC must reach the internal
power-on reset (POR) rising threshold. Once this
threshold is reached, proper operation of all aspects of
the ISL6556A is guaranteed. Hysteresis between the
rising and falling thresholds assure that once enabled,
the ISL6556A will not inadvertently turn off unless the
bias voltage drops substantially (see
Electrical
Specifications
).
2. The ISL6556A features an enable input (EN) for power
sequencing between the controller bias voltage and
another voltage rail. The enable comparator holds the
ISL6556A in shutdown until the voltage at EN rises above
1.24V. The enable comparator has about 100mV of
hysteresis to prevent bounce. It is important that the
driver ICs reach their POR level before the ISL6556A
becomes enabled. The schematic in Figure 8
demonstrates sequencing the ISL6556A with the
HIP660X family of Intersil MOSFET drivers, which require
12V bias.
3. (ISL6556ACR only) The voltage on ENLL must be logic
high to enable the controller. This pin is typically
connected to the VID_PGOOD. The ISL6556ACB has
this signal internally connected high.
4. The VID code must not be 111111 or 111110. These codes
signal the controller that no load is present. The controller
will enter shut-down mode after receiving either of these
codes and will execute soft start upon receiving any other
code. These codes can be used to enable or disable the
controller but it is not recommended. After receiving one
of these codes, the controller executes a 2-cycle delay
before changing the overvoltage trip level to the shut-
down level and disabling PWM. Overvoltage shutdown
cannot be reset using one of these codes.
To enable the controller, VCC must be greater than the POR
threshold; the voltage on EN must be greater than 1.24V; for
ISL6556ACR, ENLL must be logic high; and VID cannot be
equal to 111111 or 111110. When each of these conditions is
true, the controller immediately begins the soft-start
sequence.
C
REF
R
RE
F
4 T
VID
=
(EQ. 9)
FIGURE 8. POWER SEQUENCING USING THRESHOLD-
SENSITIVE ENABLE (EN) FUNCTION
-
+
1.24V
EXTERNAL CIRCUIT
ISL6556A INTERNAL CIRCUIT
EN
+12V
POR
CIRCUIT
10.7k
1.40k
ENABLE
COMPARATOR
SOFT START
AND
FAULT LOGIC
ENLL
(ISL6556ACR only)
VCC
ISL6556A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6556ACB-T | Optimized Multi-Phase PWM Controller with 6-Bit DAC for VR10.X Application |
| ISL6556ACBZ-T | Optimized Multi-Phase PWM Controller with 6-Bit DAC for VR10.X Application |
| ISL6556BCRZ-T | Optimized Multi-Phase PWM Controller with 6-Bit DAC and Programmable Internal Temperature Compensation for VR10.X Application |
| ISL6556BCBZ | Optimized Multi-Phase PWM Controller with 6-Bit DAC and Programmable Internal Temperature Compensation for VR10.X Application |
| ISL6556BCR-T | Optimized Multi-Phase PWM Controller with 6-Bit DAC and Programmable Internal Temperature Compensation for VR10.X Application |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6556ACRZ-TR5208 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6556BCB | 功能描述:IC CTRLR MULTIPHASE VRM10 28SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6556BCB-T | 功能描述:IC CTRLR MULTIPHASE VRM10 28SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6556BCBZ | 功能描述:電流型 PWM 控制器 VRM 10 0 MULTI-PHS CONTROLLER RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6556BCBZ | 制造商:Intersil Corporation 功能描述:Pulse Width Modulation (PWM) Controller |
發布緊急采購，3分鐘左右您將得到回復。