- 您現在的位置：買賣IC網 > PDF目錄383156 > ISL6558IBZ (INTERSIL CORP) Multi-Purpose Precision Multi-Phase PWM Controller With Optional Active Voltage Positioning PDF資料下載
參數資料
| 型號： | ISL6558IBZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Multi-Purpose Precision Multi-Phase PWM Controller With Optional Active Voltage Positioning |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | GREEN, PLASTIC, MS-012-AC, SOIC-16 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 474K |
| 代理商： | ISL6558IBZ |
14
FN9027.12
June 21, 2005
The total output ripple current can be determined from the
curves in Figure 10. They provide the total ripple current as a
function of duty cycle and number of active channels,
normalized to the parameter K
NORM
at zero duty cycle.
LxFSW
where L is the channel inductor value.
Find the intersection of the active channel curve and duty
cycle for your particular application. The resulting ripple
current multiplier from the y-axis is then multiplied by the
normalization factor, K
NORM
, to determine the total output
ripple current for the given application.
INPUT CAPACITOR SELECTION
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use ceramic capacitors for
the high frequency decoupling and bulk capacitors to supply
the RMS current. Small ceramic capacitors can be placed
very close to the upper MOSFET to suppress the voltage
induced in the parasitic circuit impedances.
Two important parameters to consider when selecting the
bulk input capacitor are the voltage rating and the RMS
current rating. For reliable operation, select a bulk capacitor
with voltage and current ratings above the maximum input
voltage and largest RMS current required by the circuit. The
capacitor voltage rating should be at least 1.25 times greater
than the maximum input voltage and a voltage rating of 1.5
times is a conservative guideline. The RMS current
requirement for a converter design can be approximated with
the aid of Figure 11. Follow the curve for the number of active
channels in the converter design. Next determine the duty
cycle for the converter and find the intersection of this value
and the active channel curve. Find the corresponding y-axis
value, which is the current multiplier. Multiply the total full load
output current, not the channel value, by the current multiplier
value found and the result is the RMS input current whi
c
h
must be supported by the input capacitors.
MOSFET SELECTION AND CONSIDERATIONS
The ISL6558 requires two N-Channel power MOSFETs per
active channel or more if parallel MOSFETs are employed.
These MOSFETs should be selected based upon r
DS(ON)
,
total gate charge, and thermal management requirements.
In high-current PWM applications, the MOSFET power
dissipation, package selection and heatsink are the
dominant design factors. The power dissipation includes two
loss components; conduction loss and switching loss. These
losses are distributed between the upper and lower
MOSFETs according to duty cycle of the converter (see the
equations below). The conduction losses are the main
component of power dissipation for the lower MOSFETs, Q2
and Q4 of Figure 1. Only the upper MOSFETs, Q1 and Q3
have significant switching losses, since the lower device turn
on and off into near zero voltage.
The following equations assume linear voltage-current
transitions and do not model power loss due to the reverse-
recovery of the lower MOSFETs body diode. The gate-
charge losses are dissipated in the HIP660x drivers and
don’t heat the MOSFETs. However, large gate-charge
increases the switching time, t
SW
which increases the upper
MOSFET switching losses. Ensure that both MOSFETs are
within their maximum junction temperature at high ambient
temperature by calculating the temperature rise according to
package thermal-resistance specifications. A separate
heatsink may be necessary depending upon MOSFET
power, package type, ambient temperature and air flow.
2
r
IN
KNORM
--VOUT
=
(EQ. 11)
1.0
0.8
0.6
0.4
0.2
0
0
0.1
0.2
0.3
0.4
0.5
DUTY CYCLE (V
O
/V
IN
)
SINGLE
CHANNEL
2 CHANNEL
3 CHANNEL
4 CHANNEL
FIGURE 10. RIPPLE CURRENT vs DUTY CYCLE
C
C
ITOTAL
D
KNORMxKCM
=
(EQ. 12)
0.5
0.4
0.3
0.2
0.1
0
0
0.1
0.2
0.3
0.4
0.5
DUTY CYCLE (V
O
/V
IN
)
C
SINGLE
CHANNEL
3 CHANNEL
4 CHANNEL
2 CHANNEL
FIGURE 11. CURRENT MULTIPLIER vs DUTY CYCLE
P
UPPER
I
------------------------------------------------------------
×
V
×
I
---------------------------------------------------------
V
×
t
×
F
×
+
=
(EQ. 13)
P
LOWER
I
--------------------------------------------------------------------------------
2
r
×
IN
V
V
–
(
)
×
=
(EQ. 14)
ISL6558
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6558IBZ-T | Multi-Purpose Precision Multi-Phase PWM Controller With Optional Active Voltage Positioning |
| ISL6558IBZA | Multi-Purpose Precision Multi-Phase PWM Controller With Optional Active Voltage Positioning |
| ISL6558IBZA-T | Multi-Purpose Precision Multi-Phase PWM Controller With Optional Active Voltage Positioning |
| ISL6558EVAL1 | Multi-Purpose Precision Multi-Phase PWM Controller With Optional Active Voltage Positioning |
| ISL6558EVAL2 | Multi-Purpose Precision Multi-Phase PWM Controller With Optional Active Voltage Positioning |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6558IBZ-T | 功能描述:IC REG CTRLR BUCK PWM 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6558IR | 功能描述:IC REG CTRLR BUCK PWM 20-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6558IR-T | 功能描述:IC REG CTRLR BUCK PWM 20-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6558IRZ | 功能描述:IC REG CTRLR BUCK PWM 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6558IRZA | 功能描述:IC REG CTRLR BUCK PWM 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。