- 您現在的位置：買賣IC網 > PDF目錄383157 > ISL6559CR (INTERSIL CORP) Multi-Phase PWM Controller PDF資料下載
參數資料
| 型號： | ISL6559CR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Multi-Phase PWM Controller |
| 中文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC32 |
| 封裝： | 5 X 5 MM, PLASTIC, MO-220-VHHD, MLFP-32 |
| 文件頁數： | 8/21頁 |
| 文件大?。?/td> | 606K |
| 代理商： | ISL6559CR |
8
FN9084.8
December 29, 2004
across the R
DS(ON)
of the lower MOSFET while it is
conducting. The resulting current into the ISEN pin is
proportional to the channel current, I
L
. The ISEN current is
then sampled and held after sufficient settling time every
switching cycle. The sampled current, I
n
, is used for channel-
current balance, load-line regulation, overcurrent protection,
and module current sharing. From Figure 3, the following
equation for I
n
is derived:
r
(
)
ISEN
where I
L
is the channel current.
If R
DS(ON)
sensing is not desired, an independent current-
sense resistor in series with the lower MOSFET source can
serve as a sense element. The circuitry shown in Figure 3
represents channel n of an N-channel converter. This
circuitry is repeated for each channel in the converter, but
may not be active depending upon the status of the PWM3
and PWM4 pins as described in the previous section.
Channel-Current Balance
The sampled current, I
n
, from each active channel is used to
gauge both overall load current and the relative channel
current carried in each leg of the converter. The individual
sample currents are summed and divided by the number of
active channels. The resulting average current, I
AVG
,
provides a measure of the total load current demand on the
converter and the appropriate level of channel current. Using
Figures 3 and 4, the average current is defined as
where N is the number of active channels and I
OUT
is the
total load current.
The average current is then subtracted from the individual
channel sample currents. The resulting error current, I
ER
, is
then filtered before it adjusts V
COMP
. The modified V
COMP
signal is compared to a sawtooth ramp signal and produces
a pulse width which corrects for any unbalance and drives
the error current toward zero. Figure 4 illustrates Intersil’s
patented current-balance method as implemented on
channel-1 of a multi-phase converter.
Two considerations designers face are MOSFET selection
and inductor design. Both are significantly improved when
channel currents track at any load level. The need for
complex drive schemes for multiple MOSFETs, exotic
magnetic materials, and expensive heat sinks is avoided.
Resulting in a cost-effective and easy to implement solution
relative to single-phase conversion. Channel-current balance
insures the thermal advantage of multi-phase conversion is
realized. Heat dissipation is spread over multiple channels
and a greater area than single phase approaches.
In some circumstances, it may be necessary to deliberately
design some channel-current unbalance into the system. In
a highly compact design, one or two channels may be able to
cool more effectively than the other(s) due to nearby air flow
or heat sinking components. The other channel(s) may have
more difficulty cooling with comparatively less air flow and
heat sinking. The hotter channels may also be located close
to other heat-generating components tending to drive their
temperature even higher. In these cases, the proper
selection of the current sense resistors (R
ISEN
in Figure 3)
introduces channel current unbalance into the system.
Increasing the value of R
ISEN
in the cooler channels and
decreasing it in the hotter channels moves all channels into
thermal balance at the expense of current balance.
Voltage Regulation
The output of the error amplifier, V
COMP
, is compared to the
sawtooth waveform to modulate the pulse width of the PWM
signals. The PWM signals control the timing of the Intersil
MOSFET drivers and regulate the converter output to the
specified reference voltage. Three distinct inputs to the error
amplifier determine the voltage level of V
COMP
. The internal
and external circuitry which control voltage regulation is
illustrated in Figure 5.
I
n
I
L
-R
=
(EQ. 3)
FIGURE 3. INTERNAL AND EXTERNAL CURRENT-SENSING
CIRCUITRY
I
n
ISEN
IL
(
)
rRISEN
=
-
+
ISEN(n)
R
ISEN
SAMPLE
&
HOLD
ISL6559 INTERNAL CIRCUIT
EXTERNAL CIRCUIT
V
IN
CHANNEL N
UPPER MOSFET
CHANNEL N
LOWER MOSFET
-
+
ILrDS ON
(
)
I
L
FIGURE 4. CHANNEL-1 PWM FUNCTION AND CURRENT-
BALANCE ADJUSTMENT
÷
N
I
AVG
I
4
*
I
3
*
I
2
Σ
-
+
+
-
+
-
f(j
ω
)
PWM1
I
1
V
COMP
SAWTOOTH SIGNAL
I
ER
NOTE: *CHANNELS 3 and 4 are OPTIONAL.
(EQ. 4)
I
AVG
I
--------------N
I
…
I
N
+
+
=
I
AVG
I
-----N
r
(
ISEN
)
-R
=
ISL6559
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6559CBZ-T | Multi-Phase PWM Controller |
| ISL6560CB | Microprocessor CORE Voltage Regulator Two-Phase Buck PWM Controller |
| ISL6560CB-T | Microprocessor CORE Voltage Regulator Two-Phase Buck PWM Controller |
| ISL6560CBZ | Microprocessor CORE Voltage Regulator Two-Phase Buck PWM Controller |
| ISL6560 | Microprocessor CORE Voltage Regulator Two-Phase Buck PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6559CR-T | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6559CRZ | 功能描述:電流型 PWM 控制器 2 TO 4 PHS BUCK CNTRLR 32L 5X5 MLFP RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6559CRZR5265 | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6559CRZ-T | 功能描述:電流型 PWM 控制器 2 TO 4 PHS BUCK CNTRLR 32L 5X5 MLFP RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6559CRZ-TR5265 | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。