- 您現在的位置：買賣IC網 > PDF目錄383158 > ISL6564IR (INTERSIL CORP) Multi-Phase PWM Controller with Linear 6-bit DAC Capable of Precision rDS(ON) or DCR Differential Current Sensing PDF資料下載
參數資料
| 型號： | ISL6564IR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Multi-Phase PWM Controller with Linear 6-bit DAC Capable of Precision rDS(ON) or DCR Differential Current Sensing |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封裝： | 6 X 6 MM, PLASTIC, MO-220-VJJD, QFN-40 |
| 文件頁數： | 19/27頁 |
| 文件大?。?/td> | 798K |
| 代理商： | ISL6564IR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
19
FN9156.2
December 27, 2004
Undervoltage Detection
The undervoltage threshold is set at 75% of the VID code.
When the output voltage at VSEN is below the undervoltage
threshold, PGOOD gets pulled low.
Overvoltage Protection
When VCC is above 1.4V, but otherwise not valid as defined
under
Power on Reset
in
Electrical Specifications
, the
overvoltage trip circuit is active using auxiliary circuitry. In
this state, an overvoltage trip occurs if the voltage at VSEN
exceeds 1.8V.
With valid VCC, the overvoltage circuit is sensitive to the
voltage at VDIFF. In this state, the trip level is 1.7V prior to
valid enable conditions being met as described in
Enable
and Disable
. The only exception to this is when the IC has
been disabled by an overvoltage trip. In that case the
overvoltage trip point is VID plus 200mV. During soft-start,
the overvoltage trip level is the higher of 1.5V or VID plus
200mV. Upon successful soft-start, the overvoltage trip level
is 200mV above VID. Two actions are taken by the ISL6564
to protect the microprocessor load when an overvoltage
condition occurs.
At the inception of an overvoltage event, all PWM outputs
are commanded low instantly (less than 20ns) until the
voltage at VSEN falls below 0.6V with valid VCC or 1.5V
otherwise. This causes the Intersil drivers to turn on the
lower MOSFETs and pull the output voltage below a level
that might cause damage to the load. The PWM outputs
remain low until VDIFF falls to the programmed DAC level
when they enter a high-impedance state. The Intersil drivers
respond to the high-impedance input by turning off both
upper and lower MOSFETs. If the overvoltage condition
reoccurs, the ISL6564 will again command the lower
MOSFETs to turn on. The ISL6564 will continue to protect
the load in this fashion as long as the overvoltage condition
recurs.
Simultaneous to the protective action of the PWM outputs,
the OVP pin pulls to VCC delivering up to 100mA to the gate
of a crowbar MOSFET or SCR placed either on the input rail
or the output rail. Turning on the MOSFET or SCR collapses
the power rail and causes a fuse placed further up stream to
blow. The fuse must be sized such that the MOSFET or SCR
will not overheat before the fuse blows. The OVP pin is
tolerant to 12V (see
Absolute Maximum Ratings
), so an
external resistor pull up can be used to augment the driving
capability. If using a pull up resistor in conjunction with the
internal overvoltage protection function, care must be taken
to avoid nuisance trips that could occur when VCC is below
2V. In that case, the controller is incapable of holding OVP
low.
Once an overvoltage condition is detected, normal PWM
operation ceases until the ISL6564 is reset. Cycling the
voltage on EN or ENLL or VCC below the POR-falling
threshold will reset the controller. Cycling the VID codes will
not reset the controller.
Overcurrent Protection
ISL6564 has two levels of overcurrent protection. Each
phase is protected from a sustained overcurrent condition on
a delayed basis, while the combined phase currents are
protected on an instantaneous basis.
In instantaneous protection mode, the ISL6564 takes
advantage of the proportionality between the load current
and the average current, I
AVG
, to detect an overcurrent
condition. See the
Channel-Current Balance
section for
more detail on how the average current is measured. The
average current is continually compared with a constant
110
μ
A reference current as shown in Figure 10. Once the
average current exceeds the reference current, a
comparator triggers the converter to shutdown.
In individual overcurrent protection mode, the ISL6564
continuously compares the current of each channel with the
same 110
μ
A reference current. If any channel current
exceeds the reference current continuously for eight
consecutive cycles, the comparator triggers the converter to
shutdown.
FIGURE 12. POWER GOOD AND PROTECTION CIRCUITRY
OVP
-
+
VID + 0.2V
VDIFF
-
+
110μA
I
AVG
-
+
DAC
REFERENCE
OV
OC
UV
PGOOD
75%
SOFT START, FAULT
AND CONTROL LOGIC
-
+
OC
I
1
REPEAT FOR
EACH CHANNEL
110μA
ISL6564
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6564IRZ | Multi-Phase PWM Controller with Linear 6-bit DAC Capable of Precision rDS(ON) or DCR Differential Current Sensing |
| ISL6564IRZ-T | Multi-Phase PWM Controller with Linear 6-bit DAC Capable of Precision rDS(ON) or DCR Differential Current Sensing |
| ISL6564CR-T | Multi-Phase PWM Controller with Linear 6-bit DAC Capable of Precision rDS(ON) or DCR Differential Current Sensing |
| ISL6565ACR | Multi-Phase PWM Controller with Precision rDS(ON) or DCR Current Sensing for VR10.X Application |
| ISL6565BCBZ | Multi-Phase PWM Controller with Precision rDS(ON) or DCR Current Sensing for VR10.X Application |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6564IR-T | 功能描述:IC REG CTRLR BUCK PWM VM 40-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6564IRZ | 功能描述:電流型 PWM 控制器 MULTI-PHS PWM CNTRLR W/0 525-1 3 VID INDU RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6564IRZ-T | 功能描述:電流型 PWM 控制器 MULTI-PHS PWM CNTRLR W/0 525-1 3 VID RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6565ACB | 功能描述:IC REG CTRLR BUCK PWM VM 28-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
| ISL6565ACB-T | 功能描述:IC REG CTRLR BUCK PWM VM 28-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。