- 您現在的位置：買賣IC網 > PDF目錄383160 > ISL6612ACB (INTERSIL CORP) Advanced Synchronous Rectified Buck MOSFET Drivers with Pre-POR OVP PDF資料下載
參數資料
| 型號： | ISL6612ACB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 功率晶體管 |
| 英文描述： | Advanced Synchronous Rectified Buck MOSFET Drivers with Pre-POR OVP |
| 中文描述： | HALF BRDG BASED MOSFET DRIVER, PDSO8 |
| 封裝： | PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 325K |
| 代理商： | ISL6612ACB |
8
FN9159.4
July 25, 2005
This feature helps prevent a negative transient on the output
voltage when the output is shut down, eliminating the
Schottky diode that is used in some systems for protecting
the load from reversed output voltage events.
In addition, more than 400mV hysteresis also incorporates
into the three-state shutdown window to eliminate PWM
input oscillations due to the capacitive load seen by the
PWM input through the body diode of the controller’s PWM
output when the power-up and/or power-down sequence of
bias supplies of the driver and PWM controller are required.
Power-On Reset (POR) Function
During initial startup, the VCC voltage rise is monitored.
Once the rising VCC voltage exceeds 9.8V (typically),
operation of the driver is enabled and the PWM input signal
takes control of the gate drives. If VCC drops below the
falling threshold of 7.6V (typically), operation of the driver is
disabled.
Pre-POR Overvoltage Protection
Prior to VCC exceeding its POR level, the upper gate is held
low and the lower gate is controlled by the overvoltage
protection circuits during initial startup. The PHASE is
connected to the gate of the low side MOSFET (LGATE),
which provides some protection to the microprocessor if the
upper MOSFET(s) is shorted during initial startup. For
complete protection, the low side MOSFET should have a
gate threshold well below the maximum voltage rating of the
load/microprocessor.
When VCC drops below its POR level, both gates pull low
and the Pre-POR overvoltage protection circuits are not
activated until VCC resets.
Internal Bootstrap Device
Both drivers feature an internal bootstrap schottky diode.
Simply adding an external capacitor across the BOOT and
PHASE pins completes the bootstrap circuit. The bootstrap
function is also designed to prevent the bootstrap capacitor
from overcharging due to the large negative swing at the
trailing-edge of the PHASE node. This reduces voltage
stress on the boot to phase pins.
The bootstrap capacitor must have a maximum voltage
rating above UVCC + 5V and its capacitance value can be
chosen from the following equation:
where Q
G1
is the amount of gate charge per upper MOSFET
at V
GS1
gate-source voltage and N
Q1
is the number of
control MOSFETs. The
V
BOOT_CAP
term is defined as the
allowable droop in the rail of the upper gate drive.
As an example, suppose two IRLR7821 FETs are chosen as
the upper MOSFETs. The gate charge, Q
G
, from the data
sheet is 10nC at 4.5V (V
GS
) gate-source voltage. Then the
Q
GATE
is calculated to be 53nC for UVCC (i.e. PVCC in
ISL6613A, VCC in ISL6612A) = 12V. We will assume a
200mV droop in drive voltage over the PWM cycle. We find
that a bootstrap capacitance of at least 0.267
μ
F is required.
Gate Drive Voltage Versatility
The ISL6612A and ISL6613A provide the user flexibility in
choosing the gate drive voltage for efficiency optimization.
The ISL6612A upper gate drive is fixed to VCC [+12V], but
the lower drive rail can range from 12V down to 5V
depending on what voltage is applied to PVCC. The
ISL6613A ties the upper and lower drive rails together.
Simply applying a voltage from 5V up to 12V on PVCC sets
both gate drive rail voltages simultaneously.
Power Dissipation
Package power dissipation is mainly a function of the
switching frequency (F
SW
), the output drive impedance, the
external gate resistance, and the selected MOSFET’s
internal gate resistance and total gate charge. Calculating
the power dissipation in the driver for a desired application is
critical to ensure safe operation. Exceeding the maximum
allowable power dissipation level will push the IC beyond the
maximum recommended operating junction temperature of
125°C. The maximum allowable IC power dissipation for the
SO8 package is approximately 800mW at room temperature,
while the power dissipation capacity in the EPSOIC and DFN
packages, with an exposed heat escape pad, is more than
2W and 1.5W, respectively. Both EPSOIC and DFN
packages are more suitable for high frequency applications.
See Layout Considerations paragraph for thermal transfer
improvement suggestions. When designing the driver into an
application, it is recommended that the following calculation
is used to ensure safe operation at the desired frequency for
C
BOOT_CAP
Q
BOOT_CAP
-------------------------------------
≥
Q
GATE
Q
-----------------------------------
UVCC
GS1
N
Q1
=
(EQ. 1)
50nC
20nC
FIGURE 2. BOOTSTRAP CAPACITANCE vs BOOT RIPPLE
VOLTAGE
V
BOOT_CAP
(V)
C
B
(
μ
F
1.6
1.4
1.2
1.
0.8
0.6
0.4
0.2
0.0
0.3
0.0
0.1
0.2
0.4
0.5
0.6
0.9
0.7
0.8
1.0
Q
GATE
= 100nC
ISL6612A, ISL6613A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6612AEIBZ-T | Circular Connector; No. of Contacts:46; Series:MS27466; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:25-46 RoHS Compliant: No |
| ISL6612A | Advanced Synchronous Rectified Buck MOSFET Drivers with Pre-POR OVP |
| ISL6612AIR | 7-Bit Bus Interfaces With 3-State Outputs 20-SO 0 to 70 |
| ISL6612AIRZ | 7-Bit Bus Interfaces With 3-State Outputs 20-SO 0 to 70 |
| ISL6612AIRZ-T | Advanced Synchronous Rectified Buck MOSFET Drivers with Pre-POR OVP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6612ACB-T | 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:低端 輸入類型:非反相 延遲時間:40ns 電流 - 峰:9A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:4.5 V ~ 35 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263 包裝:管件 |
| ISL6612ACBZ | 功能描述:IC DRIVER MOSFET SYNC BUCK 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:95 系列:- 配置:高端和低端，獨立 輸入類型:非反相 延遲時間:160ns 電流 - 峰:290mA 配置數:1 輸出數:2 高端電壓 - 最大（自引導啟動）:600V 電源電壓:10 V ~ 20 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:管件 產品目錄頁面:1381 (CN2011-ZH PDF) |
| ISL6612ACBZA | 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:6,000 系列:* |
| ISL6612ACBZAR5214 | 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:6,000 系列:* |
| ISL6612ACBZA-T | 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:6,000 系列:* |
發布緊急采購，3分鐘左右您將得到回復。