- 您現在的位置：買賣IC網 > PDF目錄1928 > ISL84525IU-T (Intersil)IC SWITCH DUAL DPDT 10MSOP PDF資料下載
參數資料
| 型號： | ISL84525IU-T |
| 廠商： | Intersil |
| 文件頁數： | 12/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH DUAL DPDT 10MSOP |
| 標準包裝： | 2,500 |
| 功能： | 開關 |
| 電路： | 2 x DPDT |
| 導通狀態電阻： | 150 歐姆 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 2 V ~ 12 V |
| 電流 - 電源： | 1µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
9
FN6042.3
February 24, 2012
Detailed Description
The ISL84524 and ISL84525 operate from a single 2V to
12V supply with low on-resistance and high speed operation.
The devices are especially well suited to portable battery
powered equipment thanks to the low operating supply
voltage (2.7V), low power consumption (3W), low leakage
currents (25nA max), and the tiny MSOP packaging. High
frequency applications also benefit from the wide bandwidth,
and the very high off isolation (75dB) and crosstalk rejection
(-85dB).
Supply Sequencing and Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. All I/O pins contain
ESD protection diodes from the pin to V+ and to GND (see
Figure 8). To prevent forward biasing these diodes, V+ must
be applied before any input signals, and the input signal
voltages must remain between V+ and GND.
If these conditions cannot be guaranteed, then precautions
must be implemented to prohibit the current and voltage at
the logic pin and signal pins from exceeding the maximum
ratings of the switch. The following two methods can be used
to provide additional protection to limit the current in the
event that the voltage at a signal pin or logic pin goes below
ground or above the V+ rail.
Logic inputs can be protected by adding a 1k resistor in
series with the logic input (see Figure 8). The resistor limits
the input current below the threshold that produces
permanent damage, and the sub-microamp input current
produces an insignificant voltage drop during normal
operation.
This method is not acceptable for the signal path inputs.
Adding a series resistor to the switch input defeats the
purpose of using a low RON switch. Connecting Schottky
diodes to the signal pins (as shown in Figure 8) will shunt the
fault current to the supply or to ground thereby protecting the
switch. These Schottky diodes must be sized to handle the
expected fault current.
Power-Supply Considerations
The ISL8452X construction is typical of most CMOS analog
switches, except that they have only two supply pins: V+ and
GND. V+ and GND drive the internal CMOS switches and
set their analog voltage limits. Unlike switches with a 13V
maximum supply voltage, the ISL8452X 15V maximum
supply voltage provides plenty of room for the 10% tolerance
of 12V supplies, as well as room for overshoot and noise
spikes.
The minimum recommended supply voltage is 2V. It is
important to note that the input signal range, switching times,
and on-resistance degrade at lower supply voltages. Refer to
the Electrical Specification tables (starting on page 3) and
Typical Performance Curves (starting on page 10) for details.
V+ and GND also power the internal logic and level shifters.
The level shifters convert the input logic levels to switched
V+ and GND signals to drive the analog switch gate
terminals.
This family of switches cannot be operated with bipolar
supplies, because the input switching point becomes
negative in this configuration.
Logic-Level Thresholds
This switch family is TTL compatible (0.8V and 2.4V) over a
supply range of 2V to 11V. At 12V the VIH level is about 2.5V.
This is still below the TTL guaranteed high output minimum
level of 2.8V, but noise margin is reduced. For best results
with a 12V supply, use a logic family that provides a VOH
greater than 3V.
The digital input stages draw supply current whenever the
digital input voltage is not at one of the supply rails. Driving
the digital input signals from GND to V+ with a fast transition
time minimizes power dissipation.
High-Frequency Performance
In 50
Ω systems, signal response is reasonably flat even past
frequency response is very consistent over varying analog
signal levels.
An OFF switch acts like a capacitor and passes higher
frequencies with less attenuation, resulting in signal feed-
through from a switch’s input to its output. Off Isolation is the
resistance to this feed-through, while Crosstalk indicates the
amount of feed-through from one switch to another.
Figure 14 details the high Off Isolation and Crosstalk
rejection provided by this family. At 10MHz, Off Isolation is
about 55dB in 50 systems, decreasing approximately 20dB
per decade as frequency increases. Higher load
impedances decrease Off Isolation and Crosstalk rejection
due to the voltage divider action of the switch OFF
impedance and the load impedance.
FIGURE 8. OVERVOLTAGE PROTECTION
GND
VCOM
VNX
V+
ADDX
OPTIONAL
PROTECTION
RESISTOR
OPTIONAL
SCHOTTKY
DIODE
OPTIONAL
SCHOTTKY
DIODE
INH
ISL84524, ISL84525
相關PDF資料 |
PDF描述 |
|---|---|
| ISL84544IP | IC SWITCH SPDT 8DIP |
| ISL84581IVZ | IC MULTIPLEXER 8X1 16TSSOP |
| ISL84582IVZ | IC MUX/DEMUX DUAL 4X1 16TSSOP |
| ISL84684IIZ-T | IC SWITCH DUAL SPDT 10WLCSP |
| ISL84684IU-T | IC SWITCH DUAL SPDT 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL84525IUZ | 功能描述:IC SWITCH DUAL DPDT 10MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL84525IUZ-T | 功能描述:IC SWITCH DUAL DPDT 10MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL84541 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches |
| ISL84541_0309 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches |
| ISL84541CB | 功能描述:IC SWITCH DUAL SPST 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:- 電路:2 x SPST 導通狀態電阻:20 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):3 V ~ 5.5 V 電流 - 電源:4.1mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。