- 您現在的位置：買賣IC網 > PDF目錄11177 > ISL84684IUZ-T (Intersil)IC SWITCH DUAL SPDT 10MSOP PDF資料下載
參數資料
| 型號： | ISL84684IUZ-T |
| 廠商： | Intersil |
| 文件頁數： | 11/13頁 |
| 文件大小： | 0K |
| 描述： | IC SWITCH DUAL SPDT 10MSOP |
| 標準包裝： | 1 |
| 功能： | 開關 |
| 電路： | 2 x SPDT |
| 導通狀態電阻： | 500 毫歐 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 4.5 V |
| 電流 - 電源： | 40nA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 標準包裝 |
| 其它名稱： | ISL84684IUZ-TDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁
7
FN6088.5
July 31, 2007
During an overvoltage transient event, such as occurs during
system level IEC 61000 ESD testing, substrate currents can
be generated in the IC that can trigger parasitic SCR
structures to turn ON, creating a low impedance path from
the V+ power supply to ground. This will result in a
significant amount of current flow in the IC which can
potentially create a latch-up state or permanently damage
the IC. The external V+ resistor limits the current during this
over-stress situation and has been found to prevent latch-up
or destructive damage for many overvoltage transient
events.
Under normal operation, the sub-microamp IDD current of
the IC produces an insignificant voltage drop across the
100
Ω series resistor resulting in no impact to switch
operation or performance.
Supply Sequencing and Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. All I/O pins contain
ESD protection diodes from the pin to V+ and to GND (see
Figure 9). To prevent forward biasing these diodes, V+ must
be applied before any input signals and the input signal
voltages must remain between V+ and GND.
If these conditions cannot be guaranteed, then precautions
must be implemented to prohibit the current and voltage at
the logic pin and signal pins from exceeding the maximum
ratings of the switch. The following two methods can be used
to provide additional protection to limit the current in the
event that the voltage at a signal pin or logic pin goes below
ground or above the V+ rail.
Logic inputs can easily be protected by adding a 1k
Ω
resistor in series with the input (see Figure 9). The resistor
limits the input current below the threshold that produces
permanent damage and the sub-microamp input current
produces an insignificant voltage drop during normal
operation.
This method is not acceptable for the signal path inputs.
Adding a series resistor to the switch input defeats the
purpose of using a low rON switch. Connecting Schottky
diodes to the signal pins as shown in Figure 9 will shunt the
fault current to the supply or to ground thereby protecting the
switch. These Schottky diodes must be sized to handle the
expected fault current.
.
Power-Supply Considerations
The ISL84684 construction is typical of most single supply
CMOS analog switches, in that they have two supply pins:
V+ and GND. V+ and GND drive the internal CMOS
switches and set their analog voltage limits. Unlike switches
with a 4V maximum supply voltage, the ISL84684 5.5V
maximum supply voltage provides plenty of room for the
10% tolerance of 4.3V supplies, as well as room for
overshoot and noise spikes.
The minimum recommended supply voltage is 1.65V. It is
important to note that the input signal range, switching times,
and ON-resistance degrade at lower supply voltages. Refer
to the “Electrical Specification” tables on page 2 and “Typical
Performance Curves” on page 9 for details.
V+ and GND also power the internal logic and level shiftiers.
The level shiftiers convert the input logic levels to switched
V+ and GND signals to drive the analog switch gate
terminals.
This family of switches cannot be operated with bipolar
supplies because the input switching point becomes
negative in this configuration.
Logic-Level Thresholds
This switch family is 1.8V CMOS compatible (0.5V and 1.4V)
over a supply range of 2.7V to 4.5V (see Figure 18). At 2.7V,
the VIL level is about 0.53V. This is still above the 1.8V
CMOS guaranteed low output minimum level of 0.5V, but
noise margin is reduced.
The digital input stages draw supply current whenever the
digital input voltage is not at one of the supply rails. Driving
the digital input signals from GND to V+ with a fast transition
time minimizes power dissipation.
GND
VCOM
VNX
V+
INX
OPTIONAL
PROTECTION
RESISTOR
OPTIONAL
SCHOTTKY
DIODE
OPTIONAL
SCHOTTKY
DIODE
FIGURE 9. OVERVOLTAGE PROTECTION
ISL84684
相關PDF資料 |
PDF描述 |
|---|---|
| C8051F819-GU | IC MCU 8BIT 8KB FLASH 24QSOP |
| ISL54206AIRTZ | IC USB SWITCH DUAL SPDT 10TDFN |
| ISL54402IRUZ-T | IC USB SWITCH DUAL SPDT 10UTQFN |
| ISL43640IRZ-T | IC MUX/DEMUX 4X1 16QFN |
| ISL43410IRZ-T | IC SWITCH DPDT 16QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL84714 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Ultra Low ON-Resistance, Low Voltage, Single Supply, SPDT Analog Switch |
| ISL84714_0411 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Ultra Low ON-Resistance, Low Voltage, Single Supply, SPDT Analog Switch |
| ISL84714IH-T | 功能描述:IC SWITCH SPDT SC70-6 RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:48 系列:- 功能:開關 電路:4 x SPST - NO 導通狀態電阻:100 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| ISL84714IHZ-T | 功能描述:IC SWITCH SPDT SC70-6 RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:2,500 系列:- 功能:視頻交叉點開關 電路:1 x 8:6 導通狀態電阻:- 電壓電源:單電源 電壓 - 電源，單路/雙路(±):3.135 V ~ 5.25 V 電流 - 電源:55mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:24-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1214 (CN2011-ZH PDF) 其它名稱:FMS6502MTC24XTR |
| ISL84714IHZ-T7A | 功能描述:模擬開關 IC SUB 1OHM S SW 1 65V TO 3 6V SPDT OR 2:1 RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。