- 您現在的位置：買賣IC網 > PDF目錄383172 > ISL88013IH546Z-TK (INTERSIL CORP) 5 Ld Voltage Supervisors with Adjustable Power-On Reset, Dual Voltage Monitoring or Watchdog Timer Capability PDF資料下載
參數資料
| 型號： | ISL88013IH546Z-TK |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 5 Ld Voltage Supervisors with Adjustable Power-On Reset, Dual Voltage Monitoring or Watchdog Timer Capability |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MO-178AA, SOT-23, SC-74, 5 PIN |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 223K |
| 代理商： | ISL88013IH546Z-TK |
8
FN8093.1
December 14, 2006
Power On Reset (POR)
Applying at least 1V to the V
DD
pin activates a POR circuit
which asserts reset (i.e. RST goes HIGH while RST goes
LOW). The reset signals remain asserted until the voltage at
V
DD
and/or VMON rise above the minimum voltage sense
level for time period t
POR
. This ensures that the voltages
have stabilized.
These reset signals provide several benefits:
It prevents the system microprocessor from starting to
operate with insufficient voltage.
It prevents the processor from operating prior to
stabilization of the oscillator.
It ensures that the monitored device is held out of
operation until internal registers are properly loaded.
It allows time for an FPGA to download its configuration
prior to initialization of the circuit.
Adjusting POR Timeout via C
POR
Pin
On the ISL88011 and ISL88014, users can adjust the Power
On Reset timeout delay (t
POR
) up to many times the normal
t
POR
of 250ms. To do this, connect a capacitor between
C
POR
and ground (see Figure 3). For example, connecting a
30pF capacitor to C
POR
will increase t
POR
from a typical
250ms to about 2.5s.
NOTE:
Care should be taken in PCB
layout and capacitor placement in order to reduce stray
capacitance as much as possible, which lengthens the t
POR
timeout period.
Manual Reset
The manual reset input (MR) allows the user to trigger a
reset by using a push-button switch. The MR input is an
active-low debounced input. By connecting a push-button
directly from MR to ground, the designer adds manual
system reset capability (see Figure 4). Reset is asserted if
the MR pin is pulled low to less than 100mV for 1
μ
s or longer
while the push-button is closed. After MR is released, the
reset outputs remain asserted for t
POR
(200ms) and then
released.
Watchdog Timer
The Watchdog Timer circuit checks microprocessor activity
by monitoring the WDI input pin. The microprocessor must
periodically toggle the WDI pin within t
WDT
(1.6s nominal),
otherwise the reset signal is asserted (see Figure 5).
Internally, the 1.6s timer is cleared by either a reset or by
toggling the WDI input.
Besides the 1.6s default timeout during normal operation,
these devices also have a longer 51s timeout for startup.
During this time, a reset cannot be asserted due to the WDI
not being toggled. The longer delay at power-on allows an
operating system to boot, an FPGA to initialize, or the
system software to initialize without the burden of dealing
with the Watchdog.
Symbol Table
0
2
3
5
0
10
20
30
C
POR
(pF)
t
P
ISL88011
C
POR
ISL88014
FIGURE 3. ADJUSTING t
POR
WITH A CAPACITOR
40
50
60
70
80
4
1
6
V
DD
RST/MR
PB
ISL88012
ISL88013
ISL88014
ISL88015
R
pu
ISL88011
FIGURE 4. CONNECTING A MANUAL RESET PUSH-BUTTON
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from LOW
to HIGH
May change
from HIGH
to LOW
Will change
from LOW
to HIGH
Will change
from HIGH
to LOW
Don’t Care:
Changes
Allowed
N/A
Changing:
State Not
Known
Center Line
is High
Impedance
ISL88011, ISL88012, ISL88013, ISL88014, ISL88015
相關PDF資料 |
PDF描述 |
|---|---|
| ISL88014IH5Z-TK | 5 Ld Voltage Supervisors with Adjustable Power-On Reset, Dual Voltage Monitoring or Watchdog Timer Capability |
| ISL88015 | 5 Ld Voltage Supervisors with Adjustable Power-On Reset, Dual Voltage Monitoring or Watchdog Timer Capability(帶可調上電復位，雙電壓監控/看門狗定時器的5 Ld電壓監控器) |
| ISL88013 | 5 Ld Voltage Supervisors with Adjustable Power-On Reset, Dual Voltage Monitoring or Watchdog Timer Capability(帶可調上電復位，雙電壓監控/看門狗定時器的5 Ld電壓監控器) |
| ISL88014 | 5 Ld Voltage Supervisors with Adjustable Power-On Reset, Dual Voltage Monitoring or Watchdog Timer Capability(帶可調上電復位，雙電壓監控/看門狗定時器的5 Ld電壓監控器) |
| ISL88016 | 6-Pin Voltage Supervisors with Pin- Selectable Voltage Trip Points |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL88014EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL88014 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL88014IH5Z | 制造商:Intersil Corporation 功能描述: |
| ISL88014IH5Z-T7A | 功能描述:IC VOLT MONITR WATCHDOG SOT23-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:3.8V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) |
| ISL88014IH5Z-TK | 功能描述:監控電路 SINGLE VMON W//MR / RST RST ADJ CPOR RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| ISL88015EVAL1Z | 功能描述:BOARD EVALUATION FOR ISL88015 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。