- 您現在的位置：買賣IC網 > PDF目錄383179 > ISL9011 (Intersil Corporation) Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL9011 |
| 廠商： | Intersil Corporation |
| 英文描述： | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-SOIC -40 to 85 |
| 中文描述： | 雙路LDO穩壓器具有低噪音，低智商，及高PSRR |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 287K |
| 代理商： | ISL9011 |
11
FN9219.1
October 13, 2005
If EN2 is brought high, and EN1 goes high before the VO2
output stablizes, the ISL9011 delays the VO1 turn-on until
the VO2 output reaches its target level.
If both EN1 and EN2 are brought high at the same time, the
VO1 output has priority, and is always powered up first.
During operation, whenever the VIN voltage drops below
about 1.8V, the ISL9011 immediately disables both LDO
outputs. When VIN rises back above 2.1V, the device re-
initiates its start-up sequence and LDO operation will
resume automatically.
Reference Generation
The reference generation circuitry includes a trimmed
bandgap, a trimmed voltage reference divider, a trimmed
current reference generator, and an RC noise filter. The filter
includes the external capacitor connected to the CBYP pin.
A 0.01
μ
F capacitor connected CBYP implements a 100Hz
lowpass filter, and is recommended for most high
performance applications. For the lowest noise application, a
0.1
μ
F or greater CBYP capacitor should be used. This filters
the reference noise to below the 10Hz – 1kHz frequency
band, which is crucial in many noise-sensitive applications.
The bandgap generates a zero temperature coefficient (TC)
voltage for the reference divider. The reference divider
provides the regulation reference and other voltage
references required for current generation and over-
temperature detection.
The current generator outputs references required for
adaptive biasing as well as references for LDO output
current limit and thermal shutdown determination.
LDO Regulation and Programmable Output Divider
The LDO Regulator is implemented with a high-gain
operational amplifier driving a PMOS pass transistor. The
design of the ISL9011 provides a regulator that has low
quiescent current, fast transient response, and overall
stability across all operating and load current conditions.
LDO stability is guaranteed for a 1
μ
F to 10
μ
F output
capacitor that has a tolerance better than 20% and ESR less
than 200m
. The design is performance-optimized for a 1
μ
F
capacitor. Unless limited by the application, use of an output
capacitor value above 4.7
μ
F is not recommended as LDO
performance improvement is minimal.
Soft-start circuitry integrated into each LDO limits the initial
ramp-up rate to about 30
μ
s/V to minimize current surge. The
ISL9011 provides short-circuit protection by limiting the
output current to about 475mA.
Each LDO uses an independently trimmed 1V reference. An
internal resistor divider drops the LDO output voltage down
to 1V. This is compared to the 1V reference for regulation.
The resistor division ratio is programmed in the factory.
Overheat Detection
The bandgap outputs a proportional-to-temperature current
that is indicative of the temperature of the silicon. This
current is compared with references to determine if the
device is in danger of damage due to overheating. When the
die temperature reaches about 145°C, one or both of the
LDO’s momentarily shut down until the die cools sufficiently.
In the overheat condition, only the LDO sourcing more than
50mA will be shut off. This does not affect the operation of
the other LDO. If both LDOs source more than 50mA and an
overheat condition occurs, both LDO outputs are disabled.
Once the die temperature falls back below about 110°C, the
disabled LDO(s) are re-enabled and soft-start automatically
takes place.
ISL9011
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9011IRCMZ | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-SOIC -40 to 85 |
| ISL9011IRCRZ | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-PDIP -40 to 85 |
| ISL9011IRCRZ-T | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-PDIP -40 to 85 |
| ISL9011IRFCZ | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-SO -40 to 85 |
| ISL9011IRCJZ | Dual LDO with Low Noise, Low IQ, and High PSRR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9011_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual LDO with Low Noise, Low IQ, and High PSRR |
| ISL9011A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual LDO with Low Noise, Low IQ, and High PSRR |
| ISL9011AIRBBZ | 功能描述:IC REG LDO 1.5V .15A/.3A 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，可調式 輸出電壓:1.25 V ~ 10 V 輸入電壓:2.9 V ~ 12 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:700mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:Digi-Reel® 其它名稱:NCV8535MNADJR2GOSDKR |
| ISL9011AIRBBZ-T | 功能描述:IC REG LDO 1.5V .15A/.3A 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:2,000 系列:- 穩壓器拓撲結構:正，可調式 輸出電壓:1.2 V ~ 5 V 輸入電壓:2.5 V ~ 7 V 電壓 - 壓降（標準）:0.24V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最?。?1.2A 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-261-5，TO-261AB 供應商設備封裝:SOT-223-5 包裝:帶卷 (TR) 其它名稱:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
| ISL9011AIRBCZ | 功能描述:IC REG LDO 1.5V/1.8V 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，可調式 輸出電壓:1.25 V ~ 10 V 輸入電壓:2.9 V ~ 12 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:700mA 電流 - 限制（最小）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:Digi-Reel® 其它名稱:NCV8535MNADJR2GOSDKR |
發布緊急采購，3分鐘左右您將得到回復。