參數資料
型號: ISP1123D
廠商: NXP SEMICONDUCTORS
元件分類: 總線控制器
英文描述: Universal Serial Bus compound hub
中文描述: UNIVERSAL SERIAL BUS CONTROLLER, PDSO32
封裝: 7.50 MM, PLASTIC, SO-32
文件頁數: 8/49頁
文件大?。?/td> 1155K
代理商: ISP1123D
Philips Semiconductors
ISP1123
USB compound hub
Preliminary specification
Rev. 01 — 5 October 1999
8 of 49
9397 750 06325
Philips Electronics N.V. 1999. All rights reserved.
[1]
[2]
Symbol names with an overscore (e.g. NAME) indicate active LOW signals.
The voltage at pin V
reg(3.3)
is gated by the RESET pin. This allows fully self-powered operation by
connecting RESET to V
BUS
(+5 V USB supply). If V
BUS
is lost upstream port D+ will not be driven.
See
Table 4 “Mode selection”
.
To disable a downstream port connect both D
+
and D
to V
CC
via a 1 M
resistor; unused ports must
be disabled in reverse order starting from port 5.
Analog detection circuit can be switched off using an external EEPROM, see
Table 23
; in this case,
the pin functions as a logic input (TTL level).
Downstream ports 1 and 2 cannot be disabled.
[3]
[4]
[5]
[6]
7.
Functional description
The ISP1123 is a compound USB hub with up to 5 downstream ports. The number of
ports can be configured between 2 and 5. The downstream ports can be used to
connect low-speed or full-speed USB peripherals. Downstream port 1 is dedicated to
an embedded or non-removable function, the other ports are removable.
All standard USB requests from the host are handled by the hardware without the
need for firmware intervention. The block diagram is shown in
Figure 1
and the basic
architecture of a compound hub in
Figure 2
.
The ISP1123 requires only a single supply voltage. An internal 3.3 V regulator
provides the supply voltage for the analog USB data transceivers.
The ISP1123 supports both bus-powered and self-powered hub operation. When
using bus-powered operation a downstream port cannot supply more than 100 mA to
a peripheral. In case of self-powered operation an external supply is used to power
the downstream ports, allowing a current consumption of max. 500 mA per port.
A basic I
2
C-bus interface is provided for reading vendor ID, product ID and
configuration bits from an external EEPROM upon a reset.
7.1 Analog transceivers
The integrated transceiver interfaces directly to the USB cables through external
termination resistors. They are capable of transmitting and receiving serial data at
both ‘full-speed’ (12 Mbit/s) and ‘low-speed’ (1.5 Mbit/s) data rates. The slew rates
are adjusted according to the speed of the device connected and lie within the range
mentioned in the USB Specification Rev. 1.1
DM2
DP2
PSW1/GL1
[3]
26
27
28
AI/O
AI/O
O
downstream port 2 D
connection (analog)
[6]
downstream port 2 D
+
connection (analog)
[6]
modes 4 to 6
: power switch control output for downstream
port 1 (open-drain, 6 mA)
modes 0 to 3, 7
: GoodLink LED indicator output for
downstream port 1 (open-drain, 6 mA); to connect an LED
use a 330
series resistor
Table 3:
Symbol
[1]
Pin description for LQFP32
…continued
Pin
Type
Description
相關PDF資料
PDF描述
ISP1123NB Universal Serial Bus compound hub
ISP1130 Universal Serial Bus compound hub with integrated keyboard controller
ISP1130DL Universal Serial Bus compound hub with integrated keyboard controller
ISP1130N Universal Serial Bus compound hub with integrated keyboard controller
ISP1160 Embedded Universal Serial Bus Host Controller
相關代理商/技術參數
參數描述
ISP1123NB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub
ISP1130 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller
ISP1130DL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller
ISP1130N 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller
ISP1160 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller