- 您現在的位置：買賣IC網 > PDF目錄376009 > JAHW075A1 Analog IC PDF資料下載
參數資料
| 型號： | JAHW075A1 |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 345K |
| 代理商： | JAHW075A1 |
8
Lucent Technologies Inc.
Data Sheet
June 2000
dc-dc Converters; 36 Vdc to 75 Vdc Input, 5 Vdc Output; 50 W to 75 W
JAHW050A and JAHW075A Power Modules:
Test Configurations
8-203 (F).l
Note: Measure input reflected-ripple current with a simulated source
inductance (L
TEST
) of 12 μH. Capacitor C
S
offsets possible bat-
tery impedance. Measure current as shown above.
Figure 12. Input Reflected-Ripple Test Setup
8-513 (F).d
Note: Use a 1.0 μF ceramic capacitor and a 10 μF aluminum or tan-
talum capacitor. Scope measurement should be made using a
BNC socket. Position the load between 51 mm and 76 mm
(2 in. and 3 in.) from the module.
Figure 13. Peak-to-Peak Output Noise
Measurement Test Setup
8-749 (F)
Note: All measurements are taken at the module terminals. When
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contact resistance.
Figure 14. Output Voltage and Efficiency
Measurement Test Setup
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power mod-
ule. For the test configuration in Figure 12, a 33 μF
electrolytic capacitor (ESR < 0.7
at 100 kHz)
mounted close to the power module helps ensure sta-
bility of the unit. For other highly inductive source
impedances, consult the factory for further application
guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e.,
UL
1950,
CSA
C22.2 No. 950-95, and
VDE
0805
(EN60950, IEC950).
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75 Vdc), for the module’s output to be considered
meeting the requirements of safety extra-low voltage
(SELV), all of the following must be true:
I
The input source is to be provided with reinforced
insulation from any hazardous voltages, including the
ac mains.
I
One V
I
pin and one V
O
pin are to be grounded, or
both the input and output pins are to be kept floating.
I
The input pins of the module are not operator acces-
sible.
I
Another SELV reliability test is conducted on the
whole system, as required by the safety agencies, on
the combination of supply source and the subject
module to verify that under a single fault, hazardous
voltages do not appear at the module’s output.
Note:
Do not ground either of the input pins of the
module without grounding one of the output pins.
This may allow a non-SELV voltage to appear
between the output pin and ground.
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
The input to these units is to be provided with a maxi-
mum 15 A normal-blow fuse in the ungrounded lead.
TO OSCILLOSCOPE
CURRENT
PROBE
BATTERY
L
TEST
12
μ
H
C
220
μ
F
ESR < 0.1
@ 20
°
C, 100 kHz
33
μ
F
ESR < 0.7
@ 100 kHz
V
I
(+)
V
I
(–)
1.0
μ
F
RESISTIVE
LOAD
SCOPE
COPPER STRIP
10
μ
F
V
O
(+)
V
O
(–)
V
I
(+)
I
I
I
O
SUPPLY
CONTACT
RESISTANCE
CONTACT AND
DISTRIBUTION LOSSES
LOAD
SENSE(+)
V
I
(–)
V
O
(+)
V
O
(–)
SENSE(–)
η
O
(+) – V
O
(–)
V
I
(+) – V
I
(–)
[
-V
]
I
O
]
I
I
x 100
=
%
相關PDF資料 |
PDF描述 |
|---|---|
| JAHW075F | Analog IC |
| JAHW100F | Analog IC |
| JAN1N3019TRUR-1 | surface mount silicon Zener diodes |
| JAN1N3016 | surface mount silicon Zener diodes |
| JAN1N3016A | surface mount silicon Zener diodes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| JAHW075A61 | 功能描述:DC/DC轉換器 48Vin 5Vout 75W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| JAHW075F1 | 功能描述:CONVERTER DC/DC 3.3V 50W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:JAHW 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| JAHW075F1Z | 功能描述:DC/DC轉換器 48Vin 3.3Vout 50W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| JAHW075S6R5 | 制造商:GE Energy 功能描述: |
| JAHW075Y1 | 功能描述:CONVERTER DC/DC 1.8V 27W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:JAHW 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最小）:42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
發布緊急采購，3分鐘左右您將得到回復。