- 您現在的位置：買賣IC網 > PDF目錄376009 > JAHW100F Analog IC PDF資料下載
參數資料
| 型號： | JAHW100F |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 345K |
| 代理商： | JAHW100F |
Lucent Technologies Inc.
9
Data Sheet
June 2000
dc-dc Converters; 36 Vdc to 75 Vdc Input, 5 Vdc Output; 50 W to 75 W
JAHW050A and JAHW075A Power Modules:
Feature Descriptions
Overcurrent Protection
To provide protection in an output overload condition,
the unit is provided with internal shut down and auto-
restart mechanism.
At the instance of current-limit inception, the module
enters a "hiccup" mode of operation whereby it shuts
down and automatically attempts to restart. As long as
the fault persists, the module remains in this mode.
The protection mechanism is such that the unit can
continue in this condition for a sufficient interval of time
until the fault is cleared.
Remote On/Off
Two remote on/off options are available. Positive logic
remote on/off turns the module on during a logic-high
voltage on the ON/OFF pin, and off during a logic low.
Negative logic remote on/off turns the module off dur-
ing a logic high and on during a logic low. Negative
logic, device code suffix “1,” is the factory-preferred
configuration.
To turn the power module on and off, the user must
supply a switch to control the voltage between the
on/off terminal and the V
I
(–) terminal (V
on/off
). The
switch can be an open collector or equivalent (see
Figure 15). A logic low is V
on/off
= 0 V to 1.2 V. The
maximum I
on/off
during a logic low is 1 mA. The switch
should maintain a logic-low voltage while sinking 1 mA.
During a logic high, the maximum V
on/off
generated by
the power module is 15 V. The maximum allowable
leakage current of the switch at V
on/off
= 15 V is 50 μA.
If not using the remote on/off feature, do one of the
following to turn the unit on:
I
For negative logic, short ON/OFF pin to V
I
(–).
I
For positive logic, leave ON/OFF pin open.
8-720(F).c
Figure 15. Remote On/Off Implementation
Remote Sense
Remote sense minimizes the effects of distribution
losses by regulating the voltage at the remote-sense
connections. The voltage between the remote-sense
pins and the output terminals must not exceed the out-
put voltage sense range given in the Feature Specifica-
tions table, i.e.:
[V
O
(+) – V
O
(–)] – [SENSE(+) – SENSE(–)]
≤
0.5 V
The voltage between the V
O
(+) and V
O
(–) terminals
must not exceed the minimum output overvoltage shut-
down value indicated in the Feature Specifications
table. This limit includes any increase in voltage due to
remote-sense compensation and output voltage set-
point adjustment (trim).
If not using the remote-sense feature to regulate the
output at the point of load, then connect SENSE(+) to
V
O
(+) and SENSE(–) to V
O
(–) at the module.
Although the output voltage can be increased by both
the remote sense and by the trim, the maximum
increase for the output voltage is not the sum of both.
The maximum increase is the larger of either the
remote sense or the trim. Consult the factory if you
need to increase the output voltage more than the
above limitation.
The amount of power delivered by the module is
defined as the voltage at the output terminals multiplied
by the output current. When using remote sense and
trim, the output voltage of the module can be
increased, which at the same output current would
increase the power output of the module. Care should
be taken to ensure that the maximum output power of
the module remains at or below the maximum rated
power.
8-651 (F).m
Figure 16. Effective Circuit Configuration for
Single-Module Remote-Sense Operation
SENSE(+)
V
O
(+)
SENSE(–)
V
O
(–)
V
I
(–)
+
I
on/off
ON/OFF
V
I
(+)
LOAD
V
on/off
SENSE(+)
SENSE(–)
V
I
(+)
V
I
(–)
I
O
LOAD
CONTACT AND
DISTRIBUTION LOSSES
SUPPLY
I
I
CONTACT
RESISTANCE
V
O
(+)
V
O
(–)
相關PDF資料 |
PDF描述 |
|---|---|
| JAN1N3019TRUR-1 | surface mount silicon Zener diodes |
| JAN1N3016 | surface mount silicon Zener diodes |
| JAN1N3016A | surface mount silicon Zener diodes |
| JAN1N3016ATR | surface mount silicon Zener diodes |
| JAN1N3016ATRUR-1 | surface mount silicon Zener diodes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| JAHW100F1 | 功能描述:CONVERTER DC/DC 3.3V 66W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:JAHW 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最小）:42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| JAHW100F1Z | 功能描述:DC/DC轉換器 48Vin 3.3Vout 66W Neg logic RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| JAHW100G1 | 功能描述:DC/DC轉換器 2.5V 20A 66W 9-Pin RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| JAHW100G61 | 功能描述:DC/DC轉換器 48Vin 2.5Vout 66W Neg Pin 3.68mm RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| JAHW100Y1 | 功能描述:CONVERTER DC/DC 1.8V 36W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:JAHW 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
發布緊急采購，3分鐘左右您將得到回復。