- 您現在的位置：買賣IC網 > PDF目錄9980 > KAD5512HP-12Q72 (Intersil)IC ADC 12BIT 125MSPS SGL 72-QFN PDF資料下載
參數資料
| 型號： | KAD5512HP-12Q72 |
| 廠商： | Intersil |
| 文件頁數： | 14/34頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 125MSPS SGL 72-QFN |
| 產品培訓模塊： | High-Speed Analog-to-Digital Converters |
| 標準包裝： | 1 |
| 系列： | FemtoCharge™ |
| 位數： | 12 |
| 采樣率（每秒）： | 125M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 376mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 72-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 72-QFN（10x10） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 1 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
21
FN6808.3
October 1, 2009
Nap/Sleep
Portions of the device may be shut down to save power during
times when operation of the ADC is not required. Two power
saving modes are available: Nap, and Sleep. Nap mode
reduces power dissipation to less than 163mW and recovers
to normal operation in approximately 1s. Sleep mode
reduces power dissipation to less than 6mW but requires
approximately 1ms to recover from a sleep command.
Wake-up time from sleep mode is dependent on the state of
CSB; in a typical application CSB would be held high during
sleep, requiring a user to wait 150s max after CSB is
asserted (brought low) prior to writing ‘001x’ to SPI
Register 25. The device would be fully powered up, in
normal mode 1ms after this command is written.
Wake-up from Sleep Mode Sequence (CSB high)
Pull CSB Low
Wait 150us
Write ‘001x’ to Register 25
Wait 1ms until ADC fully powered on
In an application where CSB was kept low in sleep mode, the
150s CSB setup time is not required as the SPI registers are
powered on when CSB is low, the chip power dissipation
increases by ~ 15mW in this case. The 1ms wake-up time
after the write of a ‘001x’ to register 25 still applies. It is
generally recommended to keep CSB high in sleep mode to
avoid any unintentional SPI activity on the ADC.
All digital outputs (Data, CLKOUT and OR) are placed in a
high impedance state during Nap or Sleep. The input clock
should remain running and at a fixed frequency during Nap
or Sleep, and CSB should be high. Recovery time from Nap
mode will increase if the clock is stopped, since the internal
DLL can take up to 52s to regain lock at 250MSPS.
By default after the device is powered on, the operational
state is controlled by the NAPSLP pin as shown in Table 3.
The power-down mode can also be controlled through the
SPI port, which overrides the NAPSLP pin setting. Details on
this are contained in “Serial Peripheral Interface” on
page 22. This is an indexed function when controlled from
the SPI, but a global function when driven from the pin.
Data Format
Output data can be presented in three formats: two’s
complement, Gray code and offset binary. The data format is
selected via the OUTFMT pin as shown in Table 4.
The data format can also be controlled through the SPI port,
which overrides the OUTFMT pin setting. Details on this are
contained in “Serial Peripheral Interface” on page 22.
Offset binary coding maps the most negative input voltage to
code 0x000 (all zeros) and the most positive input to 0xFFF
(all ones). Two’s complement coding simply complements
the MSB of the offset binary representation.
When calculating Gray code, the MSB is unchanged. The
remaining bits are computed as the XOR of the current bit
position and the next most significant bit. Figure 31 shows
this operation.
Converting back to offset binary from Gray code must be
done recursively, using the result of each bit for the next
lower bit as shown in Figure 32.
TABLE 3. NAPSLP PIN SETTINGS
NAPSLP PIN
MODE
AVSS
Normal
Float
Sleep
AVDD
Nap
TABLE 4. OUTFMT PIN SETTINGS
OUTFMT PIN
MODE
AVSS
Offset Binary
Float
Two’s Complement
AVDD
Gray Code
FIGURE 31. BINARY TO GRAY CODE CONVERSION
10
11
9
0
1
BINARY
10
11
9
0
GRAY CODE
1
KAD5512HP
相關PDF資料 |
PDF描述 |
|---|---|
| SI4126-F-GM | IC WLAN SYNTH (RF2/IF) 28MLP |
| KAD5512HP-12Q48 | IC ADC 12BIT 125MSPS SGL 48-QFN |
| VE-B12-MW-F2 | CONVERTER MOD DC/DC 15V 100W |
| VE-B12-MW-F1 | CONVERTER MOD DC/DC 15V 100W |
| KAD2710C-21Q68 | IC ADC 10BIT 210MSPS SGL 68-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KAD5512HP-17Q48 | 功能描述:模數轉換器 - ADC 12-BIT 170MSPS HI PERF SINGLE ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| KAD5512HP-17Q72 | 功能描述:模數轉換器 - ADC 12-BIT 170MSPS HI PERF SINGLE ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| KAD5512HP-21Q48 | 功能描述:模數轉換器 - ADC 12-BIT 210MSPS HI PERF SINGLE ADC PROG RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| KAD5512HP-21Q72 | 功能描述:模數轉換器 - ADC 12-BIT 210MSPS HI PERF SINGLE ADC PROG RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| KAD5512HP-25Q48 | 功能描述:模數轉換器 - ADC 12-BIT 250MSPS HI PERF SINGLE ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。