- 您現在的位置：買賣IC網 > PDF目錄374387 > KS0715 (SAMSUNG SEMICONDUCTOR CO. LTD.) Driver & Controller for STN LCD(STN LCD驅動器和控制器) PDF資料下載
參數資料
| 型號： | KS0715 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | Driver & Controller for STN LCD(STN LCD驅動器和控制器) |
| 中文描述： | 驅動程序 |
| 文件頁數： | 12/50頁 |
| 文件大?。?/td> | 255K |
| 代理商： | KS0715 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
KS0715 33COM/100SEG DRIVER & CONTROLLER FOR STN LCD
12
Serial Interface (PS =
“
L
”
)
When the KS0715 is active (CS1B = L & CS2 = H), serial data (DB7) and serial clock (DB6) inputs are enabled.
And when the KS0715 is not active, the internal 8-bit shift register and the 3-bit counter are reset. Serial data can
be read on the rising edge of serial clock (DB6) and converted into 8-bit parallel data on the eighth serial clock.
Serial data input is display data when RS is high and control data when RS is low. Since the clock signal (DB6) is
easy to be affected by the external noise caused by the line length, the operation check on the actual machine is
recommended.
BUSY FLAG
The busy flag indicates whether the KS0715 is operating or not. When DB7 is high in read status operation, this
device is in busy status and will accept only read status instruction. If the cycle time is correct, the microprocessor
does not need to check this flag before each instruction, which improves the microprocessor performance.
DATA TRANSFER
The KS0715 uses a bus holder and an internal data bus for data transfer with MPU. When writing data from the
MPU to the on-chip RAM, data is automatically transferred from the bus holder to the RAM as shown in Figure4.
When reading data from the on-chip RAM to MPU, the data for the initial read cycle is stored in the bus holder
(dummy read). Consequently, MPU reads this stored data from the bus holder for the next data read cycle, as
shown in Figure 5. This means that a dummy read cycle must be inserted between each pair of address sets when
a sequence of address sets is executed, so that the data of the specified address can be output with the read
display data instruction at the second read of data rather than right after the address sets.
Figure 3. Serial Interface Timing
CS1B
CS2
SID
SCLK
RS
DB5
DB6
DB7
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
相關PDF資料 |
PDF描述 |
|---|---|
| KS0717 | Driver & Controller for STN LCD(STN LCD驅動器和控制器) |
| KS0795 | Common Driver for Dot Matrix LCD(點陣LCD的驅動器) |
| KS22069BN | 2.3W DUAL AUDIO POWER AMP |
| KS2206C | 2.3W DUAL AUDIO POWER AMP |
| KS221K15 | CAP 27PF 50V 5% NPO(C0G) SMD-0603 TR-7-PA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KS0717 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:55 COM / 100 SEG DRIVER & CONTROLLER FOR STN LCD |
| KS0718 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:81 COM / 104 SEG DRIVER & CONTROLLER FOR STN LCD |
| KS0724 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:65 COM / 132 SEG DRIVER & CONTROLLER FOR STN LCD |
| KS0741 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:128 SEG / 129 COM DRIVER & CONTROLLER FOR 4 GRAY SCALE STN LCD |
| KS0759 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:81 COM / 128 SEG DRIVER & CONTROLLER FOR STN LCD |
發布緊急采購，3分鐘左右您將得到回復。