參數資料
型號： KS8721SLI
廠商： Micrel Inc
文件頁數： 5/33頁
文件大小： 0K
描述： IC TXRX PHY 10/100 3.3V 48SSOP
標準包裝： 30
類型： 收發器
驅動器/接收器數： 1/1
規程： IEEE 802
電源電壓： 2.375 V ~ 2.625 V
安裝類型： 表面貼裝
封裝/外殼： 48-BSSOP（0.295"，7.50mm 寬）
供應商設備封裝： 48-SSOP
包裝： 管件
配用： 576-1010-ND - BOARD EVAL EXPERIMENT KS8721SL
May 2004
13
M9999-051704
KS8721BL/SL
Micrel
asserted. For 10BASE-T links, CRS assertion is based on reception of valid preamble, and de-assertion on reception of an
end-of-frame (EOF) marker.
Collision: Whenever the line state is half-duplex and the transmitter and receiver are active at the same time, the KS8721BL/
SL asserts its collision signal, which is asynchronous to any clock.
RMII (Reduced MII) Data Interface
RMII interface specifies a low-pin count, Reduced Media Independent Interface (RMII) intended for use between Ethernet
PHYs and Switch or Repeater ASICs. It is fully compliant with IEEE 802.3u [2].
This interface has the following characteristics:
It is capable of supporting 10Mbps and 100Mbps data rates.
A single clock reference is sourced from the MAC to PHY (or from an external source).
It provides independent 2-bit wide (di-bit) transmit and receive data paths.
It uses TTL signal levels compatible with common digital CMOS ASIC processes.
RMII Signal Definition
Direction
Signal Name
(w/respect to the PHY)
(w/respect to the MAC)
Use
REF_CLK
Input
Input or Output
Synchronous clock reference for receive, transmit and
control interface
CRS_DV
Output
Input
Carrier Sense/Receive Data Valid
RXD[1:0]
Output
Input
Receive Data
TX_EN
Input
Output
Transmit Enable
TXD[1:0]
Input
Output
Transmit Data
RX_ER
Output
Input (Not Required)
Receive Error
Reference Clock (REF_CLK)
REF_CLK is a continuous 50MHz clock that provides the timing reference for CRS_DV, RXD[1:0], TX_EN, TXD[1:0], and
RX_E. REF_CLK is sourced by the MAC or an external source. Switch implementations may choose to provide REF_CLK as
an input or an output depending on whether they provide a REF_CLK output or rely on an external clock distribution device.
Each PHY device must have an input corresponding to this clock but may use a single clock input for multiple PHYs
implemented on a single IC.
Carrier Sense/Receive Data Valid (CRS_DV)
CRS_DV is asserted asynchronously on detection of carrier due to the criteria relevant to the operating mode. That is, in
10BASE-T mode, when squelch is passed or in 100BASE-X mode when 2 noncontiguous zeroes in 10 bits are detected, the
carrier is detected.
Loss-of-carrier results in the de-assertion of CRS_DV synchronous to REF_CLK. As carrier criteria are met, CRS_DV remains
continuously asserted from the first recovered di-bit of the frame through the final recovered di-bit and is negated prior to the
first REF_CLK that follows the final di-bit.
The data on RXD[1:0] is considered valid once CRS_DV is asserted. However, since the assertion of CRS_DV is asynchronous
relative to REF_CLK, the data on RXD[1:0] remains as “00” until proper receive signal decoding takes place (see “Definition
of RXD[1:0] Behavior”).
Receive Data [1:0] (RXD[1:0])
RXD[1:0] transitions synchronously to REF_CLK. For each clock period in which CRS_DV is asserted, RXD[1:0] transfers two
bits of recovered data from the PHY. In some cases (e.g., before data recovery or during error conditions), a predetermined
value for RXD[1:0] is transferred instead of recovered data. RXD[1:0] remains as “00” to indicate idle when CRS_DV is de-
asserted. Values of RXD[1:0] other than “00” when CRS_DV is de-asserted are reserved for out-of-band signalling (to be
defined). Values other than “00” on RXD[1:0] while CRS_DV is de-asserted are ignored by the MAC/repeater. Upon assertion
of CRS_DV, the PHY ensures that RXD[1:0]=00 until proper receive decoding takes place.
Transmit Enable (TX_EN)
Transmit Enable TX_EN indicates that the MAC is presenting di-bits on TXD[1:0] on the RMII for transmission. TX_EN is
asserted synchronously with the first nibble of the preamble and remains asserted while all transmitted di-bits are presented
相關PDF資料
PDF描述
VI-J71-MX-F3 CONVERTER MOD DC/DC 12V 75W
D38999/24JB5PN CONN RCPT 5POS JAM NUT W/PINS
VE-20P-MX-F1 CONVERTER MOD DC/DC 13.8V 75W
VE-20L-MX-F4 CONVERTER MOD DC/DC 28V 75W
VI-J71-MX-F2 CONVERTER MOD DC/DC 12V 75W
相關代理商/技術參數
參數描述
KS8737 制造商:Micrel Inc 功能描述:IC, PHY TRANSCEIVER, 100MBPS, TQFP-64, Data Rate:100Mbps, Ethernet Type:10BASE-T
KS8737-EVAL 功能描述:BOARD EVAL EXPERIMENT FOR KS8737 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板
KS8761 制造商:KENDIN 功能描述:
KS8803 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:10/15 CH PLL
KS8803B 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:10/15 CH PLL
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*