- 您現在的位置：買賣IC網 > PDF目錄9691 > KSZ8021RNL (Micrel Inc)TXRX PHY 100BASE TX 3.3V 24QFN PDF資料下載
參數資料
| 型號： | KSZ8021RNL |
| 廠商： | Micrel Inc |
| 文件頁數： | 5/43頁 |
| 文件大小： | 0K |
| 描述： | TXRX PHY 100BASE TX 3.3V 24QFN |
| 標準包裝： | 75 |
| 類型： | PHY 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RMII |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 24-QFN 裸露焊盤（4x4） |
| 包裝： | 管件 |
| 其它名稱： | 576-3740-5 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
Micrel, Inc.
KSZ8021RNL / KSZ8031RNL
August 2010
13
M9999-082710-1.0
10Base-T Receive
On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit and
a PLL performs the decoding function. The Manchester-encoded data stream is separated into clock signal and NRZ data.
A squelch circuit rejects signals with levels less than 400 mV or with short pulse widths to prevent noise at the RXP and
RXM inputs from falsely triggering the decoder. When the input exceeds the squelch limit, the PLL locks onto the
incoming signal and the KSZ8021/31RNL decodes a data frame. The receive clock is kept active during idle periods in
between data reception.
Scrambler/De-Scrambler (100Base-TX Only)
The scrambler is used to spread the power spectrum of the transmitted signal to reduce EMI and baseline wander, and
the de-scrambler is needed to recover the scrambled signal.
PLL Clock Synthesizer
The KSZ8021/31RNL in RMII – 25MHz Clock Mode generates all internal clocks and all external clocks for system timing
from an external 25MHz crystal, oscillator, or reference clock. For the KSZ8021/31RNL in RMII – 50MHz Clock Mode,
these clocks are generated from an external 50MHz oscillator or system clock.
Auto-Negotiation
The KSZ8021/31RNL conforms to the auto-negotiation protocol, defined in Clause 28 of the IEEE 802.3 Specification.
Auto-negotiation allows UTP (Unshielded Twisted Pair) link partners to select the highest common mode of operation.
During auto-negotiation, link partners advertise capabilities across the UTP link to each other, and then compare their own
capabilities with those they received from their link partners. The highest speed and duplex setting that is common to the
two link partners is selected as the mode of operation.
The following list shows the speed and duplex operation mode from highest to lowest priority.
Priority 1: 100Base-TX, full-duplex
Priority 2: 100Base-TX, half-duplex
Priority 3: 10Base-T, full-duplex
Priority 4: 10Base-T, half-duplex
If auto-negotiation is not supported or the KSZ8021/31RNL link partner is forced to bypass auto-negotiation, then the
KSZ8021/31RNL sets its operating mode by observing the signal at its receiver. This is known as parallel detection, and
allows the KSZ8021/31RNL to establish link by listening for a fixed signal protocol in the absence of auto-negotiation
advertisement protocol.
Auto-negotiation is enabled by either hardware pin strapping (ANEN_SPEED, pin 23) or software (register 0h, bit [12]).
By default, auto-negotiation is enabled after power-up or hardware reset. Afterwards, auto-negotiation can be enabled or
disabled by register 0h, bit [12]. If auto-negotiation is disabled, the speed is set by register 0h, bit [13], and the duplex is
set by register 0h, bit [8].
The auto-negotiation link up process is shown in Figure 1.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B41-MW-F2 | CONVERTER MOD DC/DC 12V 100W |
| MS3126E20-41SX | CONN PLUG 41POS STRAIGHT W/SCKT |
| VE-B2Y-MV-F3 | CONVERTER MOD DC/DC 3.3V 99W |
| MS27474T10B98SB | CONN RCPT 6POS JAM NUT W/SCKT |
| VE-B1Z-MV-F2 | CONVERTER MOD DC/DC 2V 60W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8021RNL TR | 功能描述:以太網 IC 3.3V, 100Base-FX Physical Layer Transceiver with RMII support (24-QFN) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8021RNL-EVAL | 功能描述:以太網開發工具 3.3V, 100Base-FX Physical Layer Transceiver w/ RMII Support - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8021RNL-TR | 功能描述:1/1 Transceiver Full RMII 24-QFN (4x4) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:過期 類型:收發器 協議:RMII 驅動器/接收器數:1/1 雙工:全 接收器滯后:- 數據速率:- 電壓 - 電源:1.8V，2.5V，3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商器件封裝:24-QFN（4x4） 標準包裝:1 |
| KSZ8031RNL | 功能描述:TXRX PHY 100BASE TX 3.3V 24QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| KSZ8031RNL TR | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ RMII Support (24-QFN) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。