- 您現在的位置：買賣IC網 > PDF目錄10129 > KSZ8041NL AM (Micrel Inc)IC TXRX PHY 10/100 AUTO 32-MLF PDF資料下載
參數資料
| 型號： | KSZ8041NL AM |
| 廠商： | Micrel Inc |
| 文件頁數： | 16/54頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX PHY 10/100 AUTO 32-MLF |
| 特色產品： | Micrel Drives Ethernet Into the Global Automotive World |
| 標準包裝： | 60 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | MII，RMII |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，32-MLF? |
| 供應商設備封裝： | 32-MLF?（5x5） |
| 包裝： | 管件 |
| 配用： | 576-1621-ND - BOARD EVALUATION FOR KSZ8041NL |
| 其它名稱： | 576-3296-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
Micrel, Inc.
KSZ8041NL/RNL
September 2010
23
M9999-090910-1.4
MII Management (MIIM) Interface
The KSZ8041NL/RNL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input /
Output (MDIO) Interface. This interface allows upper-layer devices to monitor and control the state of the
KSZ8041NL/RNL. An external device with MIIM capability is used to read the PHY status and/or configure the PHY
settings. Further details on the MIIM interface can be found in Clause 22.2.4 of the IEEE 802.3 Specification.
The MIIM interface consists of the following:
A physical connection that incorporates the clock line (MDC) and the data line (MDIO).
A specific protocol that operates across the aforementioned physical connection that allows a external controller
to communicate with one or more PHY devices. Each KSZ8041NL/RNL device is assigned a unique PHY address
between 1 and 7 by its PHYAD[2:0] strapping pins. Also, every KSZ8041NL/RNL device supports the broadcast
PHY address 0, as defined per the IEEE 802.3 Specification, which can be used to read/write to a single
KSZ8041NL/RNL device, or write to multiple KSZ8041NL/RNL devices simultaneously.
A set of 16-bit MDIO registers. Register [0:6] are required, and their functions are defined per the IEEE 802.3
Specification. The additional registers are provided for expanded functionality.
The Table 1 shows the MII Management frame format for the KSZ8041NL/RNL.
Preamble
Start of
Frame
Read/Write
OP Code
PHY
Address
Bits [4:0]
REG
Address
Bits [4:0]
TA
Data
Bits [15:0]
Idle
Read
32 1’s
01
10
00AAA
RRRRR
Z0
DDDDDDDD_DDDDDDDD
Z
Write
32 1’s
01
00AAA
RRRRR
10
DDDDDDDD_DDDDDDDD
Z
Table 1. MII Management Frame Format
Interrupt (INTRP)
INTRP (pin 21) is an optional interrupt signal that is used to inform the external controller that there has been a status
update to the KSZ8041NL/RNL PHY register. Bits[15:8] of register 1Bh are the interrupt control bits, and are used to
enable and disable the conditions for asserting the INTRP signal. Bits[7:0] of register 1Bh are the interrupt status bits, and
are used to indicate which interrupt conditions have occurred. The interrupt status bits are cleared after reading register
1Bh.
Bit 9 of register 1Fh sets the interrupt level to active high or active low.
MII Data Interface (KSZ8041NL only)
The Media Independent Interface (MII) is specified in Clause 22 of the IEEE 802.3 Specification. It provides a common
interface between physical layer and MAC layer devices, and has the following key characteristics:
Supports 10Mbps and 100Mbps data rates.
Uses a 25MHz reference clock, sourced by the PHY.
Provides independent 4-bit wide (nibble) transmit and receive data paths.
Contains two distinct groups of signals: one for transmission and the other for reception.
By default, the KSZ8041NL is configured to MII mode after it is power-up or reset with the following:
A 25MHz crystal connected to XI, XO (pins 9, 8), or an external 25MHz clock source (oscillator) connected to XI.
CONFIG[2:0] (pins 18, 29, 28) set to ‘000’ (default setting).
相關PDF資料 |
PDF描述 |
|---|---|
| IDT7201LA15JI | IC MEM FIFO 512X9 15NS 32-PLCC |
| SP3086EEN-L | IC TXRX RS485/RS422 ESD 14NSOIC |
| VI-23W-IX-B1 | CONVERTER MOD DC/DC 5.5V 75W |
| MS3102R28-10PZ | CONN RCPT 7POS BOX MNT W/PINS |
| VI-23X-IX-B1 | CONVERTER MOD DC/DC 5.2V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8041NL-EVAL | 功能描述:以太網開發工具 KSZ8041NL Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8041NLI | 制造商:Micrel Inc 功能描述:IC TXRX PHY 10/100 LV/LP 32-MLF*NIC* |
| KSZ8041NLI TR | 功能描述:以太網 IC Physical Layer Transceiver 10/100BASE-T/TX (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8041NLITR | 制造商:Micrel 功能描述:Physical Layer Transceiver 1Ch 100Mbps |
| KSZ8041NLI-TR | 功能描述:1/1 Transceiver Full MII, RMII 32-MLF? (5x5) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:收發器 協議:MII，RMII 驅動器/接收器數:1/1 雙工:全 接收器滯后:- 數據速率:- 電壓 - 電源:3.135 V ~ 3.465 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤，32-MLF? 供應商器件封裝:32-MLF?（5x5） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。