- 您現在的位置：買賣IC網 > PDF目錄383230 > L292 (意法半導體) SWITCH-MODE DRIVER FOR DC MOTORS PDF資料下載
參數資料
| 型號： | L292 |
| 廠商： | 意法半導體 |
| 英文描述： | SWITCH-MODE DRIVER FOR DC MOTORS |
| 中文描述： | 開關模式直流電動機驅動 |
| 文件頁數： | 4/12頁 |
| 文件大小： | 161K |
| 代理商： | L292 |
4/12
The second input to each multipler consists of the
sign of the first input of the other multiplier before
differentiation, these are obtained using the compa-
rators C
s1
and C
s2
. The multiplier outputs, C
SA
and
C
SB
, are summed by A
3
to give the final output
signal TACHO. The peak-topeak ripple signal of the
TACHO can be found from the following expression:
V
ripple
p
p
=
π
4
(
√
2
1
)
V
thaco
DC
The max value of TACHO is:
V
tacho
max
=
π
4
√
2
V
thaco
DC
Using the coparators C
1
and C
2
another two signals
from V
AA
and V
AB
are derived - the logic signals STA
and STB.
This signals are used by the microprocessor to
determine the position by counting the pulses.
The L2910 internal reference voltage is also derived
from V
AA
and V
AB
:
V
ref
=
|
V
AA
|
+
|
V
AB
|
This reference is used by the D/A converter in the
L291 to compensate for variations in input levels,
temperature changes and ageing.
The "one pulse per rotation" opto encoder output
is connected to pin 12 of the L290 (FTF) where it is
squared to give the STF logic output for the micro-
processor.
The TACHO signal and V
ref
are sent to the L291 via
filter networks R
8
C
8
R
9
and R
6
C
7
R
7
respectively.
Pin 12 of this chip is the main summing point of the
system where TACHO and the D/A converter output
are compared.
The input to D/A converter consists of 5 bit word
plus a sign bit supplied by the microprocessor. The
sign bit represets the direction of motor rotation.
The (analogue) output of the D/A conveter -
DAC/OUT - is compared with the TACHO signal and
the risulting error signal is amplified by the error
amplifier, and subsequently appears on pin 1.
The ERRV sognal (from pin 1 , L291) is fed to pin
6 of the final chip, the L292 H-bridge motor-driver.
This input signals is bidirectional so it must be
converted to a positive signal bacause the L292
uses a single supply voltage. This is accomplished
by the first stage - the level shifter, which uses an
internally generated 8 V reference.
This same reference voltage supplies the triangle
wave oscillator whose frequency is fixed by the
external RC network (R
20
, C
17
- pins 11 and 10)
where:
1 f
osc
=
1
2RC
(
with
R
≥
8.2
K
)
The oscillator determines the switching frequency
of the output stage and should be in the range 1 to
30 KHz.
Motor current is regulated by an internal loop in the
L292 which is performed by the resistors R
18
, R
19
and the differential current sense amplifier, the out-
put of which is filtered by an external RC network
and fed back to the error amplifier.
The choise of the external components in these RC
network (pins 5, 7, 9) is determined by the motor
type and the bandwidth requirements. The values
shown in the diagram are for a 5
, 5 MH motor.
(See L292 Transfer Function Calculation in Appli-
cation Information).
The error signal obtained by the addition of the input
and the current feedback signals (pin 7) is used to
pulse width modulate the oscillator signal by means
of the comparator. The pulse width modulated sig-
nal controls the duty cycle of the Hbridge to give an
output current corresponding to the L292 input
signal.
The interval between one side of the bridge switch-
ing off and the other switching on,
τ
, is programmed
by C
17
in conjuction with an internal resistor R
τ
.
This can be foud from:
τ
=
R
τ
C
pin
10.
(
C
17
in
the
diagram
)
Since R
τ
is approximately 1.5 K
and the recom-
mended
τ
to avoid simultaneous conduction is 2.5
μ
s C
pin 10
should be around 1.5 nF.
The current sense resistors R
18
and R
19
should be
high precision types (maximum tolerance
±
2 %)
and the recommended value is given by:
R
max
I
o
max
≤
0.44 V
It is possible to synchronize two L292 ’s, if desired,
using the network shown in fig. 2.
Finally, two enable inputs are provited on the L292
(pins 12 and 13-active low and high respectively).
Thus the output stage may be inhibited by taking
pin 12 high or by taking pin 13 low. The output will
also be inhibited if the supply voltage falls below 18
V.
L292
相關PDF資料 |
PDF描述 |
|---|---|
| L293C | PUSH-BRIDGE DRIVER PUSH-PULL FOUR CHANNEL/DUAL |
| L293 | PUSH-PULL FOUR CHANNEL DRIVER WITH DIODES |
| L296PHT | HIGH CURRENT SWITCHINGREGULATORS |
| L296 | HIGH CURRENT SWITCHINGREGULATORS |
| L296P | HIGH CURRENT SWITCHINGREGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L292 | 制造商:STMicroelectronics 功能描述:IC SWITCH MODE DRIVER 292 |
| L292_03 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SWITCH-MODE DRIVER FOR DC MOTORS |
| L292B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| L292H | 功能描述:馬達/運動/點火控制器和驅動器 DC Switch-Mode RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L293 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PUSH-PULL FOUR CHANNEL DRIVER WITH DIODES |
發布緊急采購，3分鐘左右您將得到回復。