- 您現在的位置：買賣IC網 > PDF目錄30712 > L3G3250ATR (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA16 PDF資料下載
參數資料
| 型號： | L3G3250ATR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| 封裝： | 3.50 X 3.00 MM, 1.00 MM HEIGHT, GREEN, PLASTIC, LGA-16 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 257K |
| 代理商： | L3G3250ATR |
Mechanical and electrical specifications
L3G3250A
8/12
Doc ID 022118 Rev 1
2.4
Terminology
2.4.1
Sensitivity
An angular rate gyroscope is a device that produces a positive-going digital output for
counter-clockwise rotation around the sensitive axis considered. Sensitivity describes the
gain of the sensor and can be determined by applying a defined angular velocity to it. This
value changes very little over temperature and time.
2.4.2
Zero-rate level
Zero-rate level describes the actual output signal if there is no angular rate present. Zero-
rate level of precise MEMS sensors is, to some extent, a result of stress to the sensor and
therefore zero-rate level can slightly change after mounting the sensor onto a printed circuit
board or after exposing it to extensive mechanical stress.
2.4.3
Self-test (ST)
Self-test allows the testing of the mechanical and electric parts of the sensor, allowing the
seismic mass to be moved by means of an electrostatic test-force. When the ST is activated
by the IC, an actuation force is applied to the sensor, emulating a definite Coriolis force. In
this case the sensor output will exhibit a change in the output. When ST is active, the device
output is given by the algebraic sum of the signals produced by the velocity acting on the
sensor and by the electrostatic test-force.
2.5
Sleep mode, self-test and power-down
The L3G3250A enables advanced power saving functionality thanks to the different
operating modes available. When the device is set in the Sleep mode configuration, the
reading chain is completely turned off, allowing lower power consumption. In this condition,
the device turn-on time is significantly reduced permitting simpler external power cycling.
The user can select the desired operating mode through two dedicated pins.
2.6
Soldering information
The LGA package is compliant with the ECOPACK, RoHS and “Green” standard.
It is qualified for soldering heat resistance according to JEDEC J-STD-020.
Leave “Pin 1 Indicator” unconnected during soldering.
Land pattern and soldering recommendations are available at www.st.com/mems.
Table 6.
Sleep mode, self-test and power-down mode configuration
Operating mode
ST pin
Sleep pin
Normal mode
0
Power-down
0
1
Self-test
1
0
Sleep mode
1
相關PDF資料 |
PDF描述 |
|---|---|
| L3G3250A | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| L4620 | SPECIALTY CONSUMER CIRCUIT, PDIP8 |
| L48DB12001PSA | DC-DC REG PWR SUPPLY MODULE |
| L4981BD | 2 A POWER FACTOR CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDSO20 |
| L4981B | 2 A POWER FACTOR CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L3-G41N-GVW | 制造商:Sloan AG 功能描述: |
| L3G4200D | 功能描述:螺旋儀 Mems Sensor 3-Axis 2.4 to 3.6 V Gyro RoHS:否 制造商:Murata 傳感軸:Triple 靈敏度: 輸出類型:Digital 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:5 mA 封裝 / 箱體: |
| L3G4200D_1012 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS motion sensor: ultra-stable three-axis digital output gyroscope |
| L3G4200DH | 功能描述:螺旋儀 Digital Gyro 96 FIFO 250 / 500 / 2000 DPS RoHS:否 制造商:Murata 傳感軸:Triple 靈敏度: 輸出類型:Digital 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:5 mA 封裝 / 箱體: |
| L3G4200DHTR | 功能描述:螺旋儀 Digital Gyro 96 FIFO 250 / 500 / 2000 DPS RoHS:否 制造商:Murata 傳感軸:Triple 靈敏度: 輸出類型:Digital 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:5 mA 封裝 / 箱體: |
發布緊急采購，3分鐘左右您將得到回復。