- 您現在的位置：買賣IC網 > PDF目錄69003 > L6227Q (STMICROELECTRONICS) BRUSH DC MOTOR CONTROLLER, 2.8 A, QCC32 PDF資料下載
參數資料
| 型號： | L6227Q |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 2.8 A, QCC32 |
| 封裝： | 5 X 5 MM, 1 MM HEIGHT, 0.50 MM PITCH, ROHS COMPLIANT, VFQFPN-32 |
| 文件頁數： | 4/27頁 |
| 文件大?。?/td> | 435K |
| 代理商： | L6227Q |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Circuit description
L6227Q
12/27
4.3
Truth table
4.4
PWM current control
The L6227Q includes a constant off time PWM current controller for each of the two bridges.
The current control circuit senses the bridge current by sensing the voltage drop across an
external sense resistor connected between the source of the two lower power MOS
transistors and ground, as shown in Figure 9. As the current in the load builds up the voltage
across the sense resistor increases proportionally. When the voltage drop across the sense
resistor becomes greater than the voltage at the reference input (VREF
A or VREFB) the
sense comparator triggers the monostable switching the low-side MOS off. The low-side
MOS remain off for the time set by the monostable and the motor current recirculates in the
upper path. When the monostable times out the bridge will again turn on. Since the internal
dead time, used to prevent cross conduction in the bridge, delays the turn on of the power
MOS, the effective off time is the sum of the monostable time plus the dead time.
Figure 9.
PWM current controller simplified schematic
Table 7.
Truth table
Inputs
Outputs
Description (1)
1.
Valid only in case of load connected between OUT1 and OUT2
EN
IN1
IN2
OUT1
OUT2
LX (2)
2.
X = don't care
X
High Z (3)
3.
High Z = high impedance output
High Z
Disable
H
L
GND
Brake mode (lower path)
H
L
Vs
GND (Vs)
Forward
H
L
H
GND (Vs) (4)
4.
GND (Vs) = GND during Ton, Vs during Toff
Vs
Reverse
H
Vs
Brake mode (upper path)
相關PDF資料 |
PDF描述 |
|---|---|
| L6228D | STEPPER MOTOR CONTROLLER, 2.8 A, PDSO24 |
| L6228N | STEPPER MOTOR CONTROLLER, 2.8 A, PDIP24 |
| L6229QTR | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, QCC32 |
| L6229Q | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, QCC32 |
| L6230PDTR | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6227Q_09 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DMOS dual full bridge driver with PWM current controller |
| L6227QTR | 功能描述:功率驅動器IC DMOS DUAL FULL Bridge w/ PWM RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| L6228 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DMOS DRIVER FOR BIPOLAR STEPPER MOTOR |
| L6228D | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6228DTR | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。