- 您現在的位置：買賣IC網 > PDF目錄43900 > L6254 (STMICROELECTRONICS) DISK DRIVE MOTOR CONTROLLER, 2.1 A, PQFP44 PDF資料下載
參數資料
| 型號： | L6254 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | DISK DRIVE MOTOR CONTROLLER, 2.1 A, PQFP44 |
| 封裝： | 10 X 10 MM, TQFP-44 |
| 文件頁數： | 4/17頁 |
| 文件大?。?/td> | 170K |
| 代理商： | L6254 |
INTERNAL REGISTER DEFINITION
Reg:
Name:
Type:
Address:
7
Spindle Status Register
Read only
7Eh
BIT
LABEL
DESCRIPTION
0
THERMAL
Thermal Shutdown = 0 indicates that the chip temperature has exceeded 160°C.
The bit will reset (=1) when the temperature falls below 130°C. When Thermal
Shutdown =0, the spindle logic will tristate both high and low side drivers,
protecting the output circuitry.
1
THERM_WARN
Thermal Shutdown Warning =0 indicates that the chip temperature is
approximately 25°C before the device goes in thermal shut down.
2
ROTOR_STUCK
0 = A sequential Spindle BEMF has not been detected
3
FAULT
1 = Rapid deceleration of the Spindle motor or High frequency on FCOM signal.
4
MASK_TIME
Mask Time toggled to "0" indicates that the Spindle BEMF is masked.
5
ERROR_LOCK
0 = Indicates error Spindle speed > 16msec/sample, either electrical or
mechanical.
6
ALIGN
0 indicate that the Spindle is in the Internal Start-Up Align Phase.
7
GO
0 indicate that the Spindle is in the Internal Start-Up Go Phase.
Reg:
Name:
Type:
Address:
8
Spindle FLL Register
Write only
8Eh
BIT
LABEL
DESCRIPTION
0
SSLEW
Spindle PWM (chopping) Slew Rate. 0 = 10V
S, 1 = 20VS
1
ICP
Spindle FLL Charge pump current. 1= 25
A, 0 = 100A.
2
Unused. Set = 0.
3
ISNS
1 = Puts output of the Spindle sense amplifier on FCOM pin and changes limit to
roughly 1/3 of normal.
4
IL1
Adjust maximum voltage on Spindle Rsense
5
IL0
Adjust maximum voltage on Spindle Rsense
6
CPL
1 = Spindle FLL Charge pump low
7
CPH
1 = Spindle FLL Charge pump high
"IL0"
"IL1"
"ISNS"
V(I_SENSE) LIMIT (
±10%)
0
0.45V
1
0
0.50V
0
1
0
0.55V
1
0
0.75V
0
1
0.15V
1
0
1
0.20V
0
1
0.25V
1
0.30V
L6254
12/17
相關PDF資料 |
PDF描述 |
|---|---|
| L6258E | STEPPER MOTOR CONTROLLER, 1.5 A, PDSO36 |
| L6275 | VOICE COIL MOTOR CONTROLLER, 2.1 A, PQFP44 |
| L6382DTR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| L6460TR | STEPPER MOTOR CONTROLLER, PQFP64 |
| L6515 | BRUSH DC MOTOR CONTROLLER, 0.01 A, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6256 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:12V COMBO |
| L6258 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PWM controlled high current DMOS universal motor driver |
| L6258_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PWM controlled high current DMOS universal motor driver |
| L6258A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Stepper Motor Controller/Driver |
| L6258E | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。