參數資料
型號: L6713ATR
廠商: STMICROELECTRONICS
元件分類: 穩壓器
英文描述: 2 A SWITCHING CONTROLLER, 225 kHz SWITCHING FREQ-MAX, PQFP64
封裝: 10 X 10 MM, TQFP-64
文件頁數: 55/64頁
文件大?。?/td> 801K
代理商: L6713ATR
L6713A
Layout guidelines
59/64
24.2
Small signal components and connections
These are small signal components and connections to critical nodes of the application as
well as bypass capacitors for the device supply (See Figure 28). Locate the bypass
capacitor (VCC, VCCDRx and Bootstrap capacitor) close to the device and refer sensible
components such as frequency set-up resistor ROSC, over current resistor ROCP and OVP
resistor ROVP to SGND. Star grounding is suggested: connect SGND to PGND plane in a
single point to avoid that drops due to the high current delivered causes errors in the device
behavior.
Warning:
Boot capacitor extra charge. Systems that do not use
Schottky diodes might show big negative spikes on the
phase pin. This spike can be limited as well as the positive
spike but has an additional consequence: it causes the
bootstrap capacitor to be over-charged. This extra-charge
can cause, in the worst case condition of maximum input
voltage and during particular transients, that boot-to-phase
voltage overcomes the abs. max. ratings also causing device
failures. It is then suggested in this cases to limit this extra-
charge by adding a small resistor in series to the boot diode
(one resistor can be enough for all the three diodes if placed
upstream the diode anode, See Figure 28) and by using
standard and low-capacitive diodes.
Figure 28.
Power connections and related connections layout (same for all phases)
Remote sensing connection must be routed as parallel nets from the FB/VSEN pins to the
load in order to avoid the pick-up of any common mode noise. Connecting these pins in
points far from the load will cause a non-optimum load regulation, increasing output
tolerance.
Locate current reading components close to the device. The PCB traces connecting the
reading point must use dedicated nets, routed as parallel traces in order to avoid the pick-up
of any common mode noise. It's also important to avoid any offset in the measurement and,
to get a better precision, to connect the traces as close as possible to the sensing elements.
Symmetrical layout is also suggested. Small filtering capacitor can be added, near the
controller, between VOUT and SGND, on the CSx- line to allow higher layout flexibility.
L
CIN
VIN
UGATEx
PHASEx
LGATEx
PGNDx
LOAD
BOOTx
PHASEx
VCC
SGND
+Vcc
C
BOOT
L
CIN
VIN
LOAD
To limit C
BOOT
Extra-Charge
相關PDF資料
PDF描述
L6716TR DUAL SWITCHING CONTROLLER, 225 kHz SWITCHING FREQ-MAX, QCC48
L6716 DUAL SWITCHING CONTROLLER, 225 kHz SWITCHING FREQ-MAX, QCC48
L6722 SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, QCC36
L6722TR SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, QCC36
L9407F SPECIALTY ANALOG CIRCUIT, PSFM8
相關代理商/技術參數
參數描述
L6714 功能描述:功率驅動器IC 4 Phase Controller RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L6714TR 功能描述:功率驅動器IC 4 Phase Controller RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L6716 制造商:STMicroelectronics 功能描述:DC DC Cntrlr Quad-OUT Sync Step Down 48-Pin VFQFPN EP Tray 制造商:STMicroelectronics 功能描述:HANDHELD & COMPUTER PM - Trays 制造商:STMicroelectronics 功能描述:2/3/4 Phase Controlr Embedded Driver
L6716TR 功能描述:開關變換器、穩壓器與控制器 2/3/4 phase CNTRL Embedded Drivers RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
L6717 制造商:STMicroelectronics 功能描述:High-Efficiency Hybrid AM2r2 Controller 48-Pin VFQFPN Tray 制造商:STMicroelectronics 功能描述:HANDHELD & COMPUTER PM - Trays 制造商:STMicroelectronics 功能描述:High EFF Hybrid CTRL I2C Embedded Driver