- 您現在的位置：買賣IC網 > PDF目錄367494 > L9214A CAP CER 220PF 3.15KVDC R3 RAD PDF資料下載
參數資料
| 型號： | L9214A |
| 英文描述： | CAP CER 220PF 3.15KVDC R3 RAD |
| 中文描述： | 低成本振鈴用戶接口 |
| 文件頁數： | 26/46頁 |
| 文件大?。?/td> | 790K |
| 代理商： | L9214A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
Preliminary Data Sheet
October 2001
Low-Cost Ringing SLIC
L9214A/G
26
Agere Systems Inc.
Applications
(continued)
Overhead Voltage
(continued)
Ring Mode
In the ring mode, to maximize ringing loop length, the
overhead is decreased to the saturation of the tip ring
drive amplifiers, a nominal 4 V. The tip to ground volt-
age is 1 V, and the ring to V
BAT1
voltage is 3 V.
The AX amplifier at VTX is active during the ring mode,
differential ring current may be sensed at VTX during
the ring mode.
Loop Range
The dc loop range for medium-loop applications is cal-
culated using:
I
LOOP
The dc loop range for short-loop applications is calcu-
lated using:
where:
V
OHH
= 19.5 (2.5 V + 17 V) and
V
OHL
= 3.4 V (2.5 V + 0.9 V)
and where:
R
L
= loop resistance, not including protection resistors.
R
P
= protection resistor value.
Rdc = SLIC internal dc feed resistance.
|V
BAT1
| and |V
BAT2
| = battery voltage magnitude.
I
LOOP
= loop current.
V
OHH
= overhead voltage when power is drawn from
V
BAT1
.
V
OHL
= overhead voltage when power is drawn from
V
BAT2
.
The point of change over between V
BAT2
and V
BAT1
occurs at:
|V
BAT2
|
–
(0.9 + 2.5) V > [(2R
P
+ R
DC
+ R
L
) * I
LOOP
] V
V
BAT2
is typically applied under off-hook conditions for
power conservation and SLIC thermal considerations.
The L9214 is intended for short- and medium-loop
applications and, therefore, will always be in current
limit during off-hook conditions. However, note that the
ringing loop length rather than the dc loop length will be
the factor to determine operating loop length. Where
V
BAT2
is insufficient to support the loop length, the
power will be taken from V
BAT1
.
Battery Reversal Rate
The rate of battery reverse is controlled or ramped by
capacitors FB1 and FB2. A chart showing FB1/FB2 val-
ues versus typical ramp time is given below. Leave
FB1 and FB2 open if it is not desired to ramp the rate of
battery reversal.
Table 19. FB1/FB2 Values vs. Typical Ramp Time at
V
BAT1
=
–
65 V
R
L
)
----------------------------------------------
2R
P
–
R
dc
–
=
R
L
----------------------------------------------
(
)
I
LOOP
2R
P
–
R
dc
–
=
C
FB1
/C
FB2
Transition Time
Fast, B3 = 0
7 ms
75 ms
145 ms
300 ms
600 ms
750 ms
830 ms
900 ms
1070 ms
Transition Time
Slow, B3 = 1
20 ms
220 ms
440 ms
900 ms
1.8 s
2.25 s
2.5 s
2.7 s
3.2 s
0.01
μ
F
0.1
μ
F
0.22
μ
F
0.47
μ
F
1.0
μ
F
1.22
μ
F
1.3
μ
F
1.4
μ
F
1.6
μ
F
相關PDF資料 |
PDF描述 |
|---|---|
| L9215A | CAP CER 2200PF 3.15KVDC R3 RAD |
| L9216A | CAP CER 270PF 3.15KVDC R3 RAD |
| L9217A | CAP CER 2700PF 3.15KVDC R3 RAD |
| L9218A | CAP CER 330PF 3.15KVDC R3 RAD |
| L9219A | CAP CER 390PF 3.15KVDC R3 RAD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9215A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Short-Loop Sine Wave Ringing SLIC |
| L9216A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Short-Loop Ringing SLIC with Ground Start |
| L9217A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM |
| L9218A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface |
| L9219A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit |
發布緊急采購，3分鐘左右您將得到回復。